Quick Reference
930925A
© 2014, CyberData Corporation, ALL RIGHTS RESERVED
© 2014, CyberData Corporation, ALL RIGHTS RESERVED
930925A
Quick Reference
Typical System Installation
Getting Started
•
Download the Operations Guide PDF file, from the Documentation web page at:
http://www.cyberdata.net/products/voip/digitalanalog/singlewireoutdoorintercom/docs.html
•
Create a plan for the locations of your Intercoms.
•
WARNING: This product should be installed by a licensed electrician according to all local electrical and building codes.
•
WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation
instructions.
•
WARNING: The PoE connector is intended for intra-building connections only and does not route to the outside plant.
•
WARNING: This enclosure is not rated for any AC voltages!
Parts
Parameter
Factory Default Setting
IP Addressing
DHCP
IP Address
a
a. Default if there is not a DHCP server present.
10.10.10.10
Web Access Username
admin
Web Access Password
admin
Subnet Mask
a
255.0.0.0
Default Gateway
a
10.0.0.1
802.3af Compliant Ethernet Switch
VoIP Intercom
IP Phone
InformaCast Server
1
2
3
4
5
6
VoIP Intercom
VoIP Intercom
*More installation and mounting
information is illustrated in the
Operations Guide.
IP-PBX
(1) Intercom
Assembly
(1) Spacer for half-inch set conduit connector
(1) 531085B hole plug assembly
Optional Accessories
(for gooseneck mounting)
(1) T-15H Torx Key
(4) Security Torx Screw
(4) Carriage bolts
(4) Carriage bolt nuts
(4) Carriage bolt washers
Optional Accessories
Connecting the Intercom (Service Loop Routing)
Securing the Intercom
Contacting CyberData
Creates Service Loop
Route Cable(s) inside Gang Box to
Creates Service Loop
Route Cable(s) inside Gang Box to
(Not Provided)
Ground Wire
Nut
Ground Lug
Ground Cable Installation
Network Cable Installation
Ground Wire
(not provided)
Ground Lug
Nut (to Ground Lug
inside of the Gang Box
Route cable(s) inside of the
Gang Box to create the service loop.
Route cable(s) inside of the
Gang Box to create the service loop.
Network Cable
(not provided)
Torx Key
Torx Screws
Faceplate &
PCB Assembly
2 Gang Box
GENERAL ALERT
Note: To mount the intercom, use methods
compliant with local electrical codes.
Caution
Equipment Hazard: Do not use an electric or power
screwdriver to fasten the face plate and PCB assembly to the
gang box. To prevent over-torque damage to the gasket, do
not apply more than 10 inch-pounds force. Over-torquing
will cause the gasket to tear, risk moisture intrusion, and
effectively void the manufacturer's warranty.
Note: More installation and mounting
information is illustrated in the Operations
Guide.
Sales: (831) 373-2601 ext. 334
Support: 831-373-2601 ext. 333
Web:
http://www.cyberdata.net/support/contactsupportvoip.php
RMA Dept: (831) 373-2601 ext. 136
Email: [email protected]
RMA Status:
http://www.cyberdata.net/support/rmastatus.html
Warranty and RMA information is available at the following website:
http://www.cyberdata.net/support/warranty/index.html
Corporate Headquarters
CyberData Corporation
3 Justin Court
Monterey, CA 93940, USA
Phone: 831-373-2601
Fax: 831-373-4193
www.CyberData.net
The IP Endpoint Co
m
pan
y
Installation Quick Reference
Singlewire InformaCast-enabled
VoIP Outdoor Intercom
011309
VoIPon www.voipon.co.uk [email protected] Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299
