background image

6

|

ni.com

|

RMX-10050/10051 User Guide

Remote-EPO

The optional Remote-EPO feature allows external control of all outlets. The toggle switch on the 
front panel selects the Remote-EPO mode.

OFF

 will prevent all outlets from being powered.

LOCAL/ON

 will enable power to all outlets, unless they are being disabled by the outlet

control bus.

REMOTE

 will place all outlets under the control of the outlet control bus. The outlet

control bus includes three 3-pin connectors which are wired in parallel. This arrangement
allows multiple PDUs to be connected in a daisy-chain configuration and controlled from
a single control panel. The connectors mounted on the PDU are Amp/TE 1-480304-0, and
the mating connector is Amp/TE 1-480305-0. The 3-pin connectors use two low-voltage
signals as follows:

Shorting the ENABLE pin to the RETURN pin with a dry contact will trigger the
Enable signal.

Opening the DISABLE pin from the RETURN pin will trigger the Disable signal.
This signal is intended to be operated from a normally-closed contact on a control
switch. Note that the DISABLE pin must be shorted to the RETURN pin to allow the
switched outlets to operate, regardless of the toggle switch positions noted above.

Note that the Disable signal has priority, so that if both signals are triggered at the same
time, the net result will be Disable.

Table 7.  

DC Inhibit Connector Pinout

Pin

Name

Description

1

PG1

Power Good Channel 1

2

INH1

Inhibit Channel 1

3

PG2

Power Good Channel 2

4

INH2

Inhibit Channel 2

5

PG3

Power Good Channel 3

6

INH3

Inhibit Channel 3

7

PG4

Power Good Channel 4

8

INH4

Inhibit Channel 4

9

GINH

Global Inhibit

10

ACOK

AC ains signal

11

+5 V

Global 5 V bias

12

COM

Common

Summary of Contents for RMX-10051











Reviews: