National Instruments PXI-8187 User Manual Download

Page: 5 / 69

National Instruments Corporation

Contents

How to Use the Documentation Set...............................................................................vii
Conventions ...................................................................................................................vii
Related Documentation..................................................................................................viii

Chapter 1
Introduction

Benefits of PXI ..............................................................................................................1-1
NI PXI-8186/8187 .........................................................................................................1-2

Description ......................................................................................................1-2
Functional Overview .......................................................................................1-2

National Instruments Software ......................................................................................1-4

Chapter 2
Installation and Configuration

Installing the NI PXI-8186/8187 ...................................................................................2-1

How to Remove the Controller from the PXI Chassis ....................................2-4

BIOS Setup ....................................................................................................................2-4

System CMOS ...............................................................................................................2-10
LabVIEW RT Configuration Switches ..........................................................................2-11
Drivers and Software .....................................................................................................2-13

Files and Directories Installed on Your Hard Drive........................................2-13

PXI Features ..................................................................................................................2-14

PXI Trigger Connectivity ................................................................................2-14

Upgrading RAM ............................................................................................................2-14
Hard Drive Recovery .....................................................................................................2-15
Installing an OS .............................................................................................................2-16

Installing from a CD-ROM .............................................................................2-16
Installing from a Network ...............................................................................2-16

Summary of Contents for PXI-8187






































































Search results

Summary of Contents for PXI-8187

Reviews:

Related manuals for PXI-8187

Brands by name

Popular brands

National Instruments PXI-8187, User Manual

Search results

Summary of Contents for PXI-8187

Reviews:

Related manuals for PXI-8187

Brands by name

Popular brands