National Instruments PXI-8187 User Manual Download Page 14 | Manualshive

Page: 14 / 69

background image

©

National Instruments Corporation

2-1

NI PXI-8186/8187 User Manual

2

Installation and Configuration

This chapter contains information about installing and configuring your
NI PXI-8186/8187 controller.

Installing the NI PXI-8186/8187

This section contains general installation instructions for the
NI PXI-8186/8187. Consult your PXI chassis user manual for specific
instructions and warnings.

1.

Plug in your chassis before installing the NI PXI-8186/8187. The
power cord grounds the chassis and protects it from electrical damage
while you install the module. (Make sure the power switch is
turned off.)

Caution

To protect both yourself and the chassis from electrical hazards, leave the chassis

powered off until you finish installing the NI PXI-8186/8187 module.

2.

Remove any filler panels blocking access to the system controller slot
(Slot 1) in the chassis.

3.

Touch the metal part of the case to discharge any static electricity that
might be on your clothes or body.

4.

Remove the protective plastic covers from the four bracket-retaining
screws as shown in Figure 2-1.

«
...
12
13
14
15
16
...
»

Summary of Contents for PXI-8187






































































Reviews:

No comments

Related manuals for PXI-8187

FRDM-STBC-SA9500

Brand: Freescale Semiconductor Pages: 2

Brand: Uniden Pages: 5

Brand: Vecow Pages: 61

Brand: uneron Pages: 13

Wisenet PRN-6400DB4

Brand: Hanwha Techwin Pages: 125

Brand: Qlogic Pages: 2

ULTRIX-FM-NS-1RU

Brand: Ross Pages: 5

Brand: SilverStone Pages: 2

Brand: Adaptec Pages: 2

Brand: IBM Pages: 8

Brand: AXIOMTEK Pages: 2

Dummy IC M3T-SSOP36B-450

Brand: Renesas Pages: 4

STEVAL-IHT003V1

Brand: ST Pages: 20

Brand: Divio Pages: 78

Brand: Hitachi Pages: 17

Brand: Hitachi Pages: 53

Brand: Hitachi Pages: 23

Brand: Hitachi Pages: 27

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands