background image

©

 National Instruments Corporation

11

Getting Started with the NI PCI-8254R

Environment

The NI 8254R is intended for indoor use only.

Operating temperature ...........................................0 °C to 55 °C

Storage temperature ...............................................–20 °C to 70 °C

Relative humidity...................................................5% to 90%, noncondensing

Pollution Degree ....................................................2

Measurement Category ..........................................I

Approved at altitudes up to 2,000 m.

Safety

This product is designed to meet the requirements of the following standards of safety for electrical 
equipment for measurement, control, and laboratory use:

IEC 61010-1, EN 61010-1 

UL 61010-1, CSA 61010-1

Note

For UL and other safety considerations, refer to the product label, or visit 

ni.com/

certification

, search by model number or product line, and click the appropriate link in the 

Certification column. 

Electromagnetic Compatibility

This product is designed to meet the requirements of the following standards of EMC for electrical 
equipment for measurement, control, and laboratory use:

EN 61326 EMC requirements; Minimum Immunity

EN 55011 Emissions; Group 1, Class A

CE, C-Tick, ICES, and FCC Part 15 Emissions; Class A

Note

 For EMC compliance, operate this device according to product documentation.

CE Compliance

This product meets the essential requirements of applicable European Directives, as amended for 
CE marking, as follows:

73/23/EEC; Low-Voltage Directive (safety)

89/336/EEC; Electromagnetic Compatibility Directive (EMC)

Note

 Refer to the Declaration of Conformity (DoC) for this product for any additional regulatory 

compliance information. To obtain the DoC for this product, visit 

ni.com/certification

search by model number or product line, and click the appropriate link in the Certification column.

Waste Electrical and Electronic Equipment (WEEE)

EU Customers

At the end of their life cycle, all products 

must

 be sent to a WEEE recycling center. 

For more information about WEEE recycling centers and National Instruments WEEE initiatives, 
visit 

ni.com/environment/weee.htm

.

Summary of Contents for NI VISION PCI-8254R














Reviews: