National Instruments NI VISION PCI-8254R Getting Started Download Page 10

©

 National Instruments Corporation

9

Getting Started with the NI PCI-8254R

The NI 8254R ships with a 2-position power connector that plugs directly into the isolated outputs 
power input connector on the NI 8254R. To wire power to the 2-position connector, complete the 
following steps:

1.

Wire the voltage output of the isolated power supply to the isolated outputs power input, labeled 

V

on the 2-position connector.

2.

Wire the common-mode signal (ground) output of the power supply to the isolated outputs 
common-mode signal input, labeled 

C

, on the 2-position connector.

Configuring the NI 8254R

After you have installed the NI 8254R and powered on your computer, Windows will recognize the 
device and assign resources to it. Use Measurement & Automation Explorer (MAX), the National 
Instruments configuration utility, to configure the IEEE 1394 camera connected to the NI 8254R for 
acquisition. Refer to the 

Measurement & Automation Explorer Help for NI-IMAQdx

 for additional 

information about configuring the NI 8254R.

Note

Before configuring the device in MAX, ensure that you installed the NI-IMAQdx driver 

software.

Specifications

The following specifications apply to the NI IEEE 1394a interface device. These specifications are 
typical at 25 °C, unless otherwise stated.

TTL Inputs and Outputs

Digital logic levels

TTL Inputs

Number of channels ...............................................2

Maximum pulse rate ..............................................2 MHz

Minimum pulse detected........................................500 ns

Power-on state........................................................Input (high-impedance) 61.9 k

Ω

pull-up to 5V

TTL Outputs

Number of channels ...............................................10

Output voltage range..............................................0 V to 5 V

Maximum pulse rate ..............................................2 MHz

Level

Minimum

Maximum

Input low voltage (V

IL

)

0 V

0.5 V

Input high voltage (V

IH

)

2.2 V

5 V

Output low voltage (V

OL

), at 5 mA

0.4 V

Output high voltage (V

OH

), at 5 mA

2.4 V

Summary of Contents for NI VISION PCI-8254R














Reviews: