background image

Getting Started with R Series Multifunction RIO

12

ni.com

9.

On the front panel, locate the numeric control labeled 

AO Voltage (bits)

. Right-click the control, 

select 

Replace

 from the shortcut menu, and select 

Knob

 from the 

Express»Numeric Controls

 

palette to change the control type to knob.

10. On the front panel, click and highlight the value in the lower limit of the knob to change the limit 

to –

32000

. Click and highlight the value in the upper limit to change the limit to 

32000

.

11. Save the VI.

12. Using the terminal block, connect analog output channel 0 to analog input channel 0 

by wiring AI0+ (RMIO pin 68) to AO0 (RMIO pin 55) and AI0– (RMIO pin 34) to 
AOGND0 (RMIO pin 21), respectively.

13. Click the 

Run

 button in 

Analog Input (Host).vi

 and adjust the knob that controls analog output 

channel 0. Notice how the change in voltage affects the reading on analog input channel 0.

Where to Go From Here

The following resources contain information for writing applications and taking measurements with 
R Series Multifunction RIO devices.

Software Documentation

LabVIEW FPGA documentation

Getting Started with LabVIEW FPGA 8.x

—This KnowledgeBase, available at 

ni.com/kb

provides links to the top resources that can be used to assist in getting started with 
programming in LabVIEW FPGA.

FPGA Module

 book in the 

LabVIEW Help

—Select 

Help»Search the LabVIEW Help

 in 

LabVIEW to view the 

LabVIEW Help

. Browse the 

FPGA Module

 book in the 

Contents

 tab 

for information about how to use the FPGA Module to create VIs that run on the NI 78

xx

device.

LabVIEW FPGA Module Release and Upgrade Notes—

Contains information about installing 

the LabVIEW FPGA Module, describes new features, and provides upgrade information. 
To access this document, refer to 

ni.com/manuals

. In LabVIEW 8.0 or later, you can 

also view the LabVIEW Manuals directory that contains this document by selecting 

Start»

All Programs»National Instruments»LabVIEW»LabVIEW Manuals

.

Summary of Contents for NI PXI-7851
















Reviews: