background image

©

 National Instruments Corporation

5

Getting Started with the NI EVS-1463

Refer to Figure 1 while completing the following steps to install the NI EVS-1463.

Figure 1.  

NI EVS-1463 Connectors

1.

Connect a USB keyboard and USB mouse to any available USB connector.

2.

Connect a DVI monitor to the DVI connector, or use the DVI splitter cable (supplied) to connect a 
VGA monitor or dual monitors. For independent displays in dual monitor mode, one monitor must 
support a DVI-D interface and the other must support a VGA analog interface. 

Note

Connect all monitors before you supply power to the NI EVS-1463.

3.

If you want to connect the NI EVS-1463 to a network, use an Ethernet cable to connect the Ethernet 
hub to the primary network connector on the NI EVS-1463.

Caution

To prevent data loss and to maintain the integrity of your Ethernet installation, do

not

 use 

a cable longer than 100 m. If you are using a 1,000 Mbps Ethernet, use a CAT 5e or CAT 6 shielded 
twisted-pair Ethernet cable. Use a shielded twisted pair Ethernet cable for maximum signal integrity.

4.

Connect devices to other connectors as required by your system configuration.

1

Primary Network Connector

2

Secondary Network Connector

3

Reset Switch

4

Audio In Connector

5

Audio Out Connector

6

Safe Mode/IP Reset/No App/
User 1/CF Master/Slave Switches

7

User 2/User 1/HDD/Power LEDs

8

CompactFlash Slot

9

Power Supply Connector

10 Grounding Lug
11 DVI-I Connector

12 MDR 26-Pin Connector
13 RS-232 Serial Connector (COM1) 
14 MXI Express x1 Connector
15 15-Pin D-SUB I/O Connector
16 USB Connectors

RESET

MXIex1

COMPACT FLASH

INPUT

10-20V

90W  MAX

USER 2
USER 1
HDD
POWER

CF MS/SL

SAFE MODE

IP

 RESET

NO APP

USER 1

1

2

3

7

8

9

11

14 1

3

16

6

5

15

12

10

TRIGGERS

CAMERA LINK

!

4

Summary of Contents for NI EVS-1463













Reviews: