background image

2.

Ensure that any anti-virus and firewall software running on the host computer allows
connections to the host computer.

Note

 

MAX uses UDP 44525. Refer to the documentation of your firewall

software for information about configuring the firewall to allow communication
through the UDP 44525.

3.

Launch MAX on the host computer.

4.

Expand 

Remote Systems

 in the configuration tree and locate your system.

Tip

 

MAX lists the system under the model number followed by the serial

number, such as NI-cRIO-9065-1856AAA.

Configuring Startup Options

Complete the following steps to configure the cRIO-9065 startup options in MAX.
1.

In MAX, expand your system under Remote Systems.

2.

Select the 

Startup Settings

 tab to configure the startup settings.

cRIO-9065 Startup Options

You can configure the following cRIO-9065 startup options.

Table 1. cRIO-9065 Startup Options

Startup Option

Description

 

 

Force Safe Mode Rebooting the cRIO-9065 with this setting on starts the cRIO-9065

without launching LabVIEW Real-Time or any startup applications. In
safe mode, the cRIO-9065 launches only the services necessary for
updating configuration and installing software.

Enable Console

Out

Rebooting the cRIO-9065 with this setting on redirects the console output
to the RS-232 serial port. You can use a serial-port terminal program to
read the IP address and firmware version of the cRIO-9065. Use a null-
modem cable to connect the RS-232 serial port to a computer. Make sure
that the serial-port terminal program is configured to the following
settings:

115,200 bits per second

Eight data bits

No parity

One stop bit

No flow control

Disable RT

Startup App

Rebooting the cRIO-9065 with this setting on prevents any LabVIEW
startup applications from running.

NI cRIO-9065 User Manual

  | 

© National Instruments

  | 

3

Summary of Contents for NI cRIO-9065



























Reviews: