background image

User LEDs

You can define the USER1 and USER FPGA1 LEDs to meet the needs of your application.
The following table lists the USER1 and USER FPGA1 LED indicators.

Table 13. User LEDs

LED

LED Color

Description

 

 

 

USER1

Green

Use LabVIEW Real-Time to define the USER1 LED with the
RT LEDs VI. For more information about the RT LEDs VI, refer
to the 

LabVIEW Help

.

USER

FPGA1

Green

Use the LabVIEW FPGA Module and NI-RIO Device Drivers
software to define the USER FPGA1 LED. Use the USER
FPGA1 LED to help debug your application or retrieve
application status. Refer to the 

LabVIEW Help

 for information

about programming this LED.

Ethernet LED Indicators

The following table lists the Ethernet LED indicators.

Table 14. Ethernet LED Indicators

LED

LED Color

LED Pattern

Indication

 

 

 

 

ACT/LINK

Off

LAN link not established

Green

Solid

LAN link established

Flashing

Activity on LAN

10/100/1000

Yellow

Solid

1,000 Mbit/s data rate selected

Green

Solid

100 Mbit/s data rate selected

Off

10 Mbit/s data rate selected

Chassis Grounding Screw

The cRIO-9065 provides a chassis grounding screw.

NI cRIO-9065 User Manual

  | 

© National Instruments

  | 

13

Summary of Contents for NI cRIO-9065



























Reviews: