National Instruments NI 9866 Getting Started Manual Download Page 21

Refer to the 

NI Trademarks and Logo Guidelines

 at 

ni.com/trademarks

 for information on

National Instruments trademarks. Other product and company names mentioned herein are
trademarks or trade names of their respective companies. For patents covering National
Instruments products/technology, refer to the appropriate location: 

Help

»

Patents

 in your software,

the 

patents.txt

 file on your media, or the 

National Instruments Patent Notice

 at 

ni.com/

patents

. You can find information about end-user license agreements (EULAs) and third-party

legal notices in the readme file for your NI product. Refer to the 

Export Compliance Information

 at

ni.com/legal/export-compliance

 for the National Instruments global trade compliance policy

and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO
EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION
CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government
Customers: The data contained in this manual was developed at private expense and is subject to
the applicable limited rights and restricted data rights as set forth in FAR 52.227-14, DFAR
252.227-7014, and DFAR 252.227-7015.

© 2012—2015 National Instruments. All rights reserved.

373710E-01

Jun15

Summary of Contents for NI 9866






















Reviews: