National Instruments NI 9866 Getting Started Manual Download Page 15 | Manualshive

Page: 15 / 21

National Instruments NI 9866 Getting Started Manual Download Page 15

Environmental

Refer to the manual for the chassis you are using for more
information about meeting these specifications.

...........................................................

Operating temperature
(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 70 °C

...........................................................

Storage temperature
(IEC 60068-2-1, IEC 60068-2-2)

-40 °C to 85 °C

...........................................................

Ingress protection

IP40

...........................................................

Operating humidity
(IEC 60068-2-78)

10% RH to 90% RH,
noncondensing

...........................................................

Storage humidity
(IEC 60068-2-78)

5% RH to 95% RH,
noncondensing

...........................................................

Pollution Degree

2

...........................................................

Maximum altitude

2,000 m

Indoor use only.

NI 9866 Getting Started Guide

|

© National Instruments

|

15

«
...
13
14
15
16
17
...
»

Summary of Contents for NI 9866






















Reviews:

No comments