background image

Caution

 When product terminals are hazardous voltage LIVE, you must

ensure that devices and circuits connected to the product are properly

insulated from human contact.

Attention

 Lorsqu'une haute tension dangereuse est appliquée aux

bornes du produit, vous devez vous assurer que les appareils et les circuits

auxquels il est connecté sont correctement isolés de tout contact humain.

Caution

 You must use the NI 9969 connector backshell kit to ensure that

the terminals are not accessible.

Safety Guidelines for Hazardous Locations

The NI-9244 is suitable for use in Class I, Division 2, Groups A, B, C, D, T4 hazardous

locations; Class I, Zone 2, AEx nA IIC T4 Gc and Ex nA IIC T4 Gc hazardous locations;

and nonhazardous locations only. Follow these guidelines if you are installing the

NI-9244 in a potentially explosive environment. Not following these guidelines may

result in serious injury or death.

Caution

 Do not disconnect I/O-side wires or connectors unless power has

been switched off or the area is known to be nonhazardous.

Caution

 Do not remove modules unless power has been switched off or

the area is known to be nonhazardous.

Caution

 Substitution of components may impair suitability for Class I,

Division 2, or Zone 2.

© National Instruments

5

NI-9244 Getting Started

Summary of Contents for NI-9244
















Reviews: