background image

2

|

ni.com

|

NI 9222/9223 Calibration Procedure

Documentation

Consult the following documents for information about the NI 9222/9223, NI-DAQmx, and 
your application software. All documents are available on 

ni.com

 and help files install with the 

software.

Test Equipment

Table 1 lists the equipment recommended for the performance verification and adjustment 
procedures. If the recommended equipment is not available, select a substitute using the 
requirements listed in Table 1.

NI cDAQ-9174/9178 USB Chassis Quick Start

NI-DAQmx installation and hardware setup

NI 9222/9223 Operating Instructions and Specifications

NI 9222/9223 specific information, specifications, and calibration interval

NI-DAQmx Readme

Operating system and application software support in NI-DAQmx

LabVIEW Help

LabVIEW programming concepts and reference information about NI-DAQmx 
VIs and functions

NI-DAQmx C Reference Help

Reference information for NI-DAQmx C functions and NI-DAQmx C properties

NI-DAQmx .NET Help Support for Visual Studio

Reference information for NI-DAQmx .NET methods and NI-DAQmx .NET 
properties, key concepts, and a C enum to .NET enum mapping table

Table 1.  

Recommended Equipment

Equipment

Recommended Model

Requirements

Calibrator

Fluke 5700A

Use a high-precision voltage source with an 
accuracy 

15 ppm and an output impedance 

50

.

Chassis

NI cDAQ-9178

Summary of Contents for NI 9223









Reviews: