background image

© 

National Instruments Corp.

19

NI 9208E Operating Instructions and Specifications

Where to Go for Support

The National Instruments Web site is your complete resource for 
technical support. At 

ni.com/support

 you have access to 

everything from troubleshooting and application development 
self-help resources to email and phone assistance from 
NI Application Engineers.

National Instruments corporate headquarters is located at 
11500 North Mopac Expressway, Austin, Texas, 78759-3504. 
National Instruments also has offices located around the world to 
help address your support needs. For telephone support in the 
United States, create your service request at 

ni.com/support

 

and follow the calling instructions or dial 512 795 8248. For 
telephone support outside the United States, contact your local 
branch office: 

Australia 1800 300 800, Austria 43 662 457990-0, 
Belgium 32 (0) 2 757 0020, Brazil 55 11 3262 3599, 
Canada 800 433 3488, China 86 21 5050 9800, 
Czech Republic 420 224 235 774, Denmark 45 45 76 26 00, 
Finland 358 (0) 9 725 72511, France 01 57 66 24 24, 
Germany 49 89 7413130, India 91 80 41190000, 
Israel 972 3 6393737, Italy 39 02 41309277, Japan 0120-527196, 

Summary of Contents for NI 9208E





















Reviews: