National Instruments NI-9146 Safety, Environmental, And Regulatory Information Download Page 16 | Manualshive

Page: 16 / 29

National Instruments NI-9146 Safety, Environmental, And Regulatory Information Download Page 16

Note

Installing software may change the network behavior of the chassis.

For information about network behavior by installed software version, go

to

and enter the Info Code ipconfigcrio.

Wiring Power to the Chassis

The NI 9146 requires an external power supply that meets the specifications in the

Power Requirements

section.

The NI 9146 filters and regulates the supplied power and provides power for all of

the I/O modules. The NI 9146 has one layer of reverse-voltage protection. Complete

the following steps to connect a power supply to the chassis.

1. Ensure that the power supply is turned off.
2. Connect the positive lead of the power supply to the V terminal of the

COMBICON power connector shipped with the NI 9146, and tighten the

terminal screw. The following figure shows the terminal screws, which secure

the wires in the screw terminals, and the connector screws, which secure the

power connector on the front panel.

Figure 13. COMBICON Power Connector

C

V

2

2

1

1. Terminal Screw
2. Connector Screws

3. Connect the negative lead of the power supply to the C terminal of the power

connector and tighten the terminal screw.

4. Install the power connector on the front panel of the NI 9146 and tighten the

connector screws.

5. Turn on the power supply.

ni.com

16

NI-9146 Safety, Environmental, and Regulatory Information

«
...
14
15
16
17
18
...
»

Summary of Contents for NI-9146






























Reviews:

No comments