background image

8

Specifications

These specifications are typical for -40° to +70° C unless otherwise 
noted.

Output Characteristics

Number of channels ......................... 8 single-ended

Resolution  ........................................ 12 bits, 1 in 4,096 

(~6 

µ

A/bit)

Isolation ............................................ 3,000 Vrms, input to output

Safety isolation, working voltage ..... 250 Vrms channel to earth 

ground, designed per 
IEC 1010

Current Output

Output Range .................................... 0-20 mA or 4-20 mA, 

programmable (0-21 mA or 
3.5-21 mA with over-range)

Type .................................................. Current source, external loop 

power required

External Loop Power ........................ 5 to 24 VDC

Resistive load.................................... up to 1 kOhm with 24 V 

loop supply, up to 100 Ohm 
with 5 V supply

Voltage Drop .................................... 3 V

Protection.......................................... Short-circuit and 

open-circuit

Default Power-on state ..................... 0 mA

Accuracy

Absolute accuracy............................. 0.2% FSR

Monotonicity .................................... Guaranteed over temperature

Offset temperature coefficient .......... 50 nA/°C

Gain temperature coefficient ............ 40 ppm/°C

Dynamic Characteristics

Max conversion rate ......................... 200 Updates/s

Slew rate  .......................................... 0.4 mA/

µ

s

FPAO200.fm  Page 8  Thursday, July 31, 1997  8:55 AM

Summary of Contents for FIeldPoint FP-AO-200













Reviews: