manualshive.com logo in svg

National Instruments FieldPoint FP-2000, Quick Start Manual, Page: 18 / 20

Share
Download
National Instruments FieldPoint FP-2000 Quick Start Manual Download Page 18

Safety

The FP-2000/2010 meets the requirements of the following standards for safety and electrical
equipment for measurement, control, and laboratory use:

• EN 61010-1:1993/A2:1995, IEC 61010-1:1990/A2:1995
• UL 3101-1:1993, UL 3111-1:1994, UL 3121:1998
• CAN/CSA c22.2 no. 1010.1:1992?A2:1997

Electromagnetic Compatibility

CE, C-Tick and FCC Part 15 (Class A) Compliant
Electrical emissions. . . . . . . . . . . . . . . . . . . EN 55011 Class A at 10 m FCC Part 15A

above 1 GHz

Electrical immunity . . . . . . . . . . . . . . . . . . . Evaluated to EN 61326: 1997/A1:1998, Table 1

NOTE:

For full EMC compliance, you must operate this device with shielded cabling.

See the Declaration of Conformity (DoC) for this product for any additional regulatory
compliance information. To obtain the DoC for this product, click

Declaration of

Conformity

at

ni.com/hardref.nsf/

.

18

322759b.qxd  7/26/01  9:52 AM  Page 18

Summary of Contents for FieldPoint FP-2000





















Reviews:

No comments