National Instruments DAQCard-6715 User Manual Download Page 6

Page: 6 / 103

Contents

ni.com

Minimizing Glitches on the Output Signal ..................................................... 3-3
AO Data Generation Methods......................................................................... 3-3

Software-Timed Generations............................................................ 3-4
Hardware-Timed Generations .......................................................... 3-4

Analog Output Triggering ............................................................................................. 3-5
Connecting Analog Output Signals ............................................................................... 3-6
Waveform Generation Timing Signals.......................................................................... 3-6

Waveform Generation Timing Summary ....................................................... 3-6
AO Start Trigger Signal .................................................................................. 3-7

Using a Digital Source...................................................................... 3-7
Outputting the AO Start Trigger Signal ........................................... 3-7

AO Pause Trigger Signal ................................................................................ 3-8

Using a Digital Source...................................................................... 3-8

AO Sample Clock Signal ................................................................................ 3-8

Using an Internal Source .................................................................. 3-9
Using an External Source ................................................................. 3-9
Outputting the AO Sample Clock Signal ......................................... 3-9
Other Timing Requirements ............................................................. 3-10

AO Sample Clock Timebase Signal................................................................ 3-11
Master Timebase Signal.................................................................................. 3-11

Getting Started with AO Applications in Software ....................................................... 3-12

Chapter 4
Digital I/O

Static DIO...................................................................................................................... 4-2
Digital Waveform Generation (NI 6731/6733 Only) .................................................... 4-2

DO Sample Clock Signal (NI 6731/6733 Only) ............................................. 4-2

Using an Internal Source .................................................................. 4-3
Using an External Source ................................................................. 4-3

Digital Waveform Acquisition (NI 6731/6733 Only) ................................................... 4-3

DI Sample Clock Signal (NI 6731/6733 Only)............................................... 4-4

Using an Internal Source .................................................................. 4-4
Using an External Source ................................................................. 4-4

I/O Protection ................................................................................................................ 4-5
Power-On States ............................................................................................................ 4-5
Connecting Digital I/O Signals ..................................................................................... 4-6
Getting Started with DIO Applications in Software...................................................... 4-7

Summary of Contents for DAQCard-6715








































































































Search results

Summary of Contents for DAQCard-6715

Reviews:

Related manuals for DAQCard-6715

Brands by name

Popular brands

National Instruments DAQCard-6715, User Manual

Search results

Summary of Contents for DAQCard-6715

Reviews:

Related manuals for DAQCard-6715

Brands by name

Popular brands