National Instruments Compact FieldPoint cFP-21 Series Quick Start Manual Download

Page: 1 / 28

Quick Start Guide

FieldPoint cFP-21

What You Need to Get Set Up

1. Mount the Compact FieldPoint Backplane

You can mount the cFP-BP-

backplane on a 35mm DIN rail, on a panel, or in a

standard 19 in. rack. Before using any of these mounting methods, record the serial
number from the back of the backplane.

Each set of mounting instructions in this document includes an instruction to
connect the protective earth (PE) ground terminal on the cFP-BP-

backplane to

the system safety ground. The backplane PE ground terminal has the following

•

cFP-21

LabVIEW RT controller

•

Mounting hardware (DIN rail,
panel-mount, or rack-mount
accessory)

•

I/O module(s)

•

cFP-BP-

backplane, connector

blocks, cables

•

11–30 VDC power supply

•

Accessories: Ethernet cable,
number 2 Phillips screwdriver

•

PC running Windows

•

FieldPoint software 4.1.1 or later

•

LabVIEW Real-Time Module

™

324033b.fm Page 1 Wednesday, September 14, 2005 2:09 PM

Summary of Contents for Compact FieldPoint cFP-21 Series





























Search results

Summary of Contents for Compact FieldPoint cFP-21 Series

Reviews:

Related manuals for Compact FieldPoint cFP-21 Series

Brands by name

Popular brands

National Instruments Compact FieldPoint cFP-21 Series, Quick Start Manual

Search results

Summary of Contents for Compact FieldPoint cFP-21 Series

Reviews:

Related manuals for Compact FieldPoint cFP-21 Series

Brands by name

Popular brands