manualshive.com logo in svg

National Instruments Compact FieldPoint cFP-21 Series, Quick Start Manual, Page: 20 / 28

Share
Download
National Instruments Compact FieldPoint cFP-21 Series Quick Start Manual Download Page 20

cFP-21xx Quick Start Guide

20

ni.com

and measurements on primary overcurrent protection devices and on ripple 
control units.

Using This Product Safely in Hazardous Locations

This product is suitable for use in U.S. and Canada: Class I, Division 2, Groups A, 
B, C, D, T4 hazardous locations; and nonhazardous locations.

Caution

Explosion hazard—Substitution of components may impair 

suitability for Class I, Division 2.

Explosion hazard—Do not disconnect equipment unless power has been 
switched off or the area is known to be nonhazardous.

Equipment must be used within its electrical and environmental ratings. 
Refer to the 

Specifications

 section. Refer to the product label for 

manufacturing location.

This product must be installed in an enclosure rated at least IP 54.

Specifications

Network

Network interface ............................. 10BaseT and 100BaseTX Ethernet

Compatibility .................................... IEEE802.3

Communication rates ........................ 10 Mbps, 100 Mbps, auto-negotiated

Maximum cabling distance............... 100 m/segment

Maximum power to
connected I/O modules ..................... 9 W

324033b.fm  Page 20  Wednesday, September 14, 2005  2:09 PM

Summary of Contents for Compact FieldPoint cFP-21 Series





























Reviews:

No comments