National Instruments AT-GPIB/TNT Getting Started Download

Page: 55 / 64

National Instruments Corporation

C-1

Appendix

Specifications

This appendix describes the physical characteristics of the
AT-GPIB/TNT, the transfer rates of the GPIB software, and the
recommended operating conditions.

Hardware Characteristics

Table C-1. AT-GPIB/TNT Hardware Characteristics

Characteristic

Specification

Dimensions

10.67 cm by 16.51 cm
(4.2 in. by 6.5 in.)

Power Requirement
(from PC AT I/O Channel)

+5 VDC

50 mA Typical
120 mA Maximum

I/O Connector

IEEE 488 Standard 24-Pin

Operating Environment

Component Temperature
Relative Humidity

0° to 55° C
10% to 90%, Noncondensing

Storage Environment

Temperature
Relative Humidity

–20° to 70° C
5% to 90%, Noncondensing

EMI

FCC Class B Certified

Summary of Contents for AT-GPIB/TNT

































































Search results

Summary of Contents for AT-GPIB/TNT

Reviews:

Related manuals for AT-GPIB/TNT

Brands by name

Popular brands

National Instruments AT-GPIB/TNT, Getting Started

Search results

Summary of Contents for AT-GPIB/TNT

Reviews:

Related manuals for AT-GPIB/TNT

Brands by name

Popular brands