manualshive.com logo in svg

National Instruments 6612, User Manual

Share
Download
National Instruments 6612 User Manual Download Page 82

5-2

|

ni.com

Chapter 5

Counter Signal Routing and Clock Generation

100 MHz Timebase

The 100 MHz Timebase can be used as the timebase for all internal subsystems.

The 100 MHz Timebase is generated from one of the following sources:
•

Onboard oscillator.

•

Various signals as shown in Figure 5-1.

20 MHz Timebase

The 20 MHz Timebase also can be used as the Source input to the 32-bit general-purpose 
counter/timers.

The 20 MHz Timebase is generated by dividing down the 100 MHz Timebase.

100 kHz Timebase

The 100 kHz Timebase also can be used as the Source input to the 32-bit general-purpose 
counter/timers.

The 100 kHz Timebase is generated by dividing down the 20 MHz Timebase by 200.

External Reference Clock

The external reference clock can be used as a source for the internal timebases (100 MHz 
Timebase, 20 MHz Timebase, and 100 kHz Timebase) on your device. By using the external 
reference clock, you can synchronize the internal timebases to an external clock.

The following signals can be routed to drive the external reference clock:
•

RTSI<0..7>

•

PFI<0..39>

•

PXI_Trigger<0..7>

•

PXIe_CLK100

1

•

PXI_STAR

1

•

PXIe-DSTAR<A, B>

1

To route a signal to the external reference clock, set the DAQmx Timing Property RefClk.Src to 
the desired signal name. 

The external reference clock is an input to a Phase-Lock Loop (PLL). The PLL generates the 
internal timebases.

1   

PXIe_CLK100, PXI_STAR, and PXIe-DSTAR<A,B> are advanced terminals. 

See 

Filtering NI-DAQmx 

Name Controls

 in 

LabVIEW Help

 for more information on showing advanced terminals.

Summary of Contents for 6612


































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands