National Instruments 6509 Programmer'S Manual Download Page 26

Page: 26 / 49

Chapter

2 Register

Map and Descriptions

National Instruments Corporation

2-15

Static DIO Register-Level Programmer Manual

Change Status Register

The Change Status Register gives the status of change detection.

Address Offset:

0x02

Type:

Read

Size:

8-bit

Bit Map:

Bit

Name

Description

7–6

Reserved

Disregard these bits.

WDT Int Status

A 1 indicates that there has been a watchdog timer
expiration that could cause an interrupt (if
watchdog timer expiration interrupts are enabled).

Falling Edge Status

A 1 indicates that there has been a falling edge that
could cause an interrupt (if falling edge interrupts
are enabled).

Rising Edge Status

A 1 indicates that there has been a rising edge that
could cause an interrupt (if rising edge interrupts
are enabled).

MasterInterrupt Status

Indicates that the device is asserting an interrupt.

OverFlow

Indicates that at least one more edge has been
detected since an interrupt is asserted.

Edge Status

Indicates an edge has been detected. If the EdgeInt
bit is set in the Master Interrupt Control Register,
Edge Status set indicates an interrupt is currently
being asserted.

Reserved

WDT Int

status

Falling

Edge

Status

Rising

Edge

Status

MasterInterrupt

Status

OverFlow

Edge

Status

Summary of Contents for 6509


















































Search results

Summary of Contents for 6509

Reviews:

Related manuals for 6509

Brands by name

Popular brands

National Instruments 6509, Programmer'S Manual

Search results

Summary of Contents for 6509

Reviews:

Related manuals for 6509

Brands by name

Popular brands