English
13
The user alone is responsible for any liabilities caused by usage other than
intended.
Commissioning and use
Any unauthorised use might cause damage to the tool. Therefore follow
these instructions:
- Always use sharp drill bits.
- Load the tool to avoid any significant reduction of speed or stoppage.
- Always change the speed gear when the machine is idle or at the
machine slow-down at low speed, in no case during the drilling or
when the machine is otherwise loaded.
Check whether the data on the name plate correspond with the actual
power supply voltage. Tools designed for 230 V may be connected also
to 220 / 240 V.
Additional handle
For safety reasons always use the additional handle (7), firmly mounted on
the clamping neck (3). The stop bar (6) can be used to adjust the drilling
depth.
Clamping a drill
Insert tool and tighten equally in all 3 holes with chuck key.
Switching on and off
By pressing the switch button (11) the machine activates and releasing the
button stops it.
Permanent run
By pressing the switch button (11) to the stop and simultaneous pressing
the latching pin (12) permanent run is achieved.
Repeated pressing the switch button (11) and its release the permanent run
is discontinued.
Speed control
By light and gradual pressing the controller button (11) you will achieve low
speed and controlled continuous run-up.
By further gradual pressing the button the speed increases to the
pre-selected speed.
Controls
1 ............ Chuck with ring gear
2 ............ Spots on spindle
3 ............ Clamping neck
4 ............ Lever for impact shifting
5 ............ Air vents
6 ............ Stop bar
7 ............ Additional handle
8 ............ Gear-shifting lever
9 ............ Alteration switch lever
10 .......... Speed pre-selection wheel
11 .......... Switch / controller
12 .......... Latching pin
13 .......... Screw shaft
14 .......... Spindle cover
15 .......... Drilling spindle
16 .......... Chuck hook
17 .......... Spanner
18 .......... Socket screw wrench
19 .......... Quick-tightening chuck
The displayed or described accessories need not be included in the delivery
package.
Double insulation
To ensure maximum safety of the user, our tools are designed and built to
satisfy applicable European standards (EN standards). Tools with double
insulation are marked by the international symbol of a double square.
These tools must not be grounded and a two-wire cable is sufficient to
supply them with power. Tools are shielded in accordance with EN 50114.
Use
The machine is intended drilling in wood, metal, ceramic and plastic.
Machines with electronic control and right/left rotation are also suitable
for screwing and thread cutting ( Only for soft screwdriving applications).
The machine is intended for impact drilling in brick, concrete and stone
as well as for drilling in wood, metal, ceramics and plastics. Machines with
electronic control and right/left rotation are also suitable for screwing and
thread-cutting.
Technical data
Drilling machine and impact drill
Type
EVP 13-2 R70
Supply voltage
230 V
Power frequency
50–60 Hz
Power input
650 W
Speed under load
1st speed gear
0–630 min
-1
2nd speed gear
0–1 730 min
-1
Idle speed
1st speed gear
0–1 100 min
-1
2nd speed gear
0–3 000 min
-1
Number of impacts
1st speed gear
0–12 600 min
-1
2nd speed gear
0–34 600 min
-1
Speed pre-selection
Right-left turning
Extent of chuck ø
1,5–13 mm
Thread on spindle
1/2“–20 UNF
Inner hexagon in spindle
1/4“
Drilling ø max
into steel
13 mm
into aluminium
16 mm
into wood
35 mm
into concrete
16 mm
Clamping neck ø
43 mm
Weight
1,8 kg
Protection class
II /