PACIFIC E35 – EG35
31 |
P a g e
PACIFIC E35 - EG35
Nardi Compressori – www.nardicompressori.com
compressor. This is set by NARDI COMPRESSORI at 225 BAR or 330 BAR according to the maximum pressure
allowed by the compressor.
To move to the next screen you must press the PAGE button again.
In this screen you can change the minimum pressure to restart the compressor in
“AUTOMATIC” mode “COMPRESSOR MINIMUN PRESSURE”. Pressing the arrow
buttons ▲(up) or ▼ (down) you can modify the value.
The standard parameter is 50 BAR. This value of minimum pressure can be
increased but it cannot be larger than 30 BAR from the value of maximum pressure (the difference between maximum
pressure and minimum pressure cannot exceed 30 BAR).
To move to the next screen you must press the PAGE button again.
This screen displays the time in hours “h” that remain until the next maintenance
service by a skilled technician.
This value is important for a proper maintenance of the compressor. The electronic
board will send a signal at 200 and 100 hours of service, to remind you to contact
your dealer to arrange an appointment for routine maintenance. These two alarms
will display the message “SERVICE TIME ALERT”, the red LED light in “GENERAL ALARMS” will turn on and it will send
an audible signal. Pressing the “RESET” button, everything will go back to normal until the third alarm Is activated with
the message “SERVICE TIME / NEED MAINTENANCE”, the red LED light in “GENERAL ALARMS” will turn on and it
will send an audible signal. Pressing the “RESET” button the compressor will still work but the message “SERVICE TIME
/ NEED MAINTENANCE” will continue showing until a technician provides service to the machine and resets the alarm.
To move to the next screen you must press the PAGE button again.
This screen displays the utility voltage in volts LINE VOLTAGE” and the current drawn
by the motor of the compressor in Ampers “MOTOR CURRENT”. This information
helps to monitor the proper functioning of the motor according to the voltage. In case
the current drawn by the motor is abnormal, this will trigger an alarm and the display
will show the message “OVER CURRENT MOTOR”, the red LED light in “GENERAL ALARMS” will turn on and it will
send an audible signal. The compressor will turn off automatically. Pressing the “RESET” button everything will go back
to normal. We strongly advise you to pay attention to this alarm because the motor has drawn more current than it
should. If this happens more than once, get in contact with technical assistance.
To move to the next screen you must press the PAGE button again.
This screen displays the temperature of the head of the last stage of the compressor.
A temperature sensor monitors the heating of this component in such a way as to
stop the compressor in case of high temperatures due to a lack of ventilation and to a
fault. This will trigger an alarm, the display will show the message “OVER
TEMPARATURE COMPRESSOR”, the red LED light in “GENERAL ALARMS” will turn on and it will send an audible
signal. The compressor will turn off automatically. Pressing the “RESET” button everything will go back to normal but we
strong advise you to pay attention to this alarm because the compressor is working at high temperature. If this happens
more than once, get in contact with technical assistance.
COMPRESSOR
MINIMUM PRESSURE
50 bar
TIME TO
SERVICE
500 h
LINE VOLTAGE 396
MOTOR CURRENT
0.0A
TEMPERATURE
COMPRESSOR
29°C
Summary of Contents for PACIFIC E35
Page 23: ...PACIFIC E35 EG35 23 P a g e PACIFIC E35 EG35 Nardi Compressori www nardicompressori com...
Page 24: ...PACIFIC E35 EG35 24 P a g e PACIFIC E35 EG35 Nardi Compressori www nardicompressori com...
Page 58: ...PACIFIC E35 EG35 58 P a g e PACIFIC E35 EG35 Nardi Compressori www nardicompressori com...
