manualshive.com logo in svg

Napoleon Tureen GD82NT-T, Installation And Operation Instructions Manual

Share
Download
Napoleon Tureen GD82NT-T Installation And Operation Instructions Manual Download Page 16

16

W415-0583 / D / 07.24.07

Optional Front

Glass Door

Latches

Retainer

Before the glass door can be removed, the optional front 
must be removed.
The glass door is secured to the top front edge of the fi rebox. 
Pull the handles of the latches forward, then lift the hooks out 
from the slots in the door frame to release the top of the door. 
Next, pivot forward until the top edge of the door clears the 
front of the fi replace.  Next gripping the sides of the door lift 
the door out from the retainer along the bottom of the door. 

FINISHING / SERVICING

FIGURE 35

DOOR REMOVAL

   1a

. Rectangular Front Removal

Pull on the top of the optional front away from the fi replace until 
the male portion of the latch disengages. Tilt forward slightly 
and lift from the 2 shoulder screws near the bottom.

1b

. Heritage and Wrought Iron Front Removal

Turn the head of each turn button from a horizontal position 
to vertical.  (Fig. 41)  Allow the front to tilt forward slightly 
and lift from the 2 shoulder screws near the bottom front.  

Note:  Fronts are heavy so when the second turn button 
is turned the front will want to fall forward.

OPTIONAL FRONT REMOVAL

FIGURE 34

Lift the panel from the slots. This will allow access and removal 
of the remote receiver and spark module.

If valve replacement is necessary follow step 1 above then 
proceed with the following ...

  

Start by sliding the bowl forward until it clears the burner then 
lift from the fi rebox.  Remove the 2 screws located behind 
the burner then lift up off the orifi ce and out.  Then using a 
fl at head screw driver remove the curved decorative panel.  
Finally remove the 2 screws holding the burner bottom in 
place. 

 (Fig. 42)

Lift the burner out from the fi rebox.

CONTROL PANEL REMOVAL

BOWL AND BURNER REMOVAL

  1

. 

Place the door frame face down careful not to scratch 

the paint. 

  2

. 

Center the gasketed glass inside the door frame with the 

thick side of the gasket facing up.

  3

. 

Bend the glass retainers located along the edge of the 

door frame over the gasket holding the glass in place. Careful 
not to break the glass.

GLASS/DOOR REPLACEMENT

Summary of Contents for Tureen GD82NT-T

































Reviews:

No comments

Brands by name

Popular brands

Load more brands