background image

7

W415-1034 /  09.01.11

When the appliance is installed at elevations above 4,500ft, and in the absence of specifi c recommendations 
from the local authority having jurisdiction, the certifi ed high altitude input rating shall be reduced at the rate of 
4% for each additional 1,000ft. Expansion / contraction noises during heating up and cooling down cycles are 
normal and to be expected.

This appliance is not approved for closet or recessed installations. It is approved for bathroom, bedroom and 
bed-sitting room installations and is suitable for mobile homes. The natural gas model is suitable for installation 
in a mobile home that is permanently positioned on its site and fuelled with natural gas.

2.5  RATING PLATE INFORMATION

INSTALLER: It is your responsibility to check off the appropriate box on the rating plate according to 
the model, venting and gas type of the appliance.

For rating plate location, see “INSTALLATION OVERVIEW” section.

This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

SERIAL NUMBER/NO. DE SERIE: 

IR3G/CIR3G

WARNING: 

DO NOT ADD ANY MATERIAL TO THE APPLIANCE THAT WILL COME IN 

CONTACT WITH THE FLAMES, OTHER THAN THAT SUPPLIED BY THE MANUFACTURER 
WITH THE APPLIANCE. 

AVERTISSEMENT:

 N'A JOUTEZ PAS A CET APPAREIL AUCUN MATERIAU DEVANT 

ENTRER EN CONTACT AVEC LES FLAMMES AUTRE QUE CELUI QUI EST FOURNI AVEC CET 
APPAREIL PAR LE FABRICANT.

W385-0659

CERTIFIED FOR
CERTIFIEE POUR

   CANADA   USA

IR3GN

IR3GP

CIR3GN

CIR3GP

MODEL

C E R T I F I E D

REFERENCE #161746 

Natural Gas/Gaz Naturel

Propane

CE FOYER À GAZ VENTILÉS NE DOIT PAS ÊTRE UTILISÉ 
CONJOINTEMENT AVEC DES FILTRES À AIR.UTILISER AVEC LES 
PORTES VITRÉES HOMOLOGUÉES AVEC CETTE UNITÉ SEULE-
MENT. UN COMBUSTIBLE SOLIDE NE DOIT PAS ETRE UTILISE 
AVEC CET APPAREIL.

CERTIFIED UNDER / HOMOLOGUÉ SELON LES NORMES: ANSI Z21.88b-2009, CSA 2.22b-2009 VENTED GAS FIREPLACE  / APPAREIL À GAZ VENTILÉS. 

WOLF STEEL LTD.

24 NAPOLEON ROAD, BARRIE. ONTARIO L4M 4Y8 CANADA

THIS VENTED GAS FIREPLACE HEATER IS NOT FOR USE 
WITH AIR FILTERS. FOR USE WITH GLASS DOORS CERTIFIED 
FOR THIS UNIT ONLY. NOT FOR USE WITH SOLID FUEL.

ELECTRICAL RATING: 

115V 1.5AMP 60HZ

THE APPLIANCE MUST BE VENTED USING THE APPROPRIATE WOLF STEEL VENT KITS. SEE 
OWNER’S INSTALLATION MANUAL FOR VENTING SPECIFICS. PROPER REINSTALLATION AND 
RESEALING IS NECESSARY AFTER SERVICING THE VENT-AIR INTAKE SYSTEM.

WARNING: 

FOR INSTALLATION INTO A VENTED NON-COMBUSTIBLE FIREPLACE ONLY. THE 

MINIMUM FIREPLACE SIZE IS: HEIGHT 20.5”, DEPTH 13.25”, WIDTH 29”. THE MINIMUM INSIDE 
FLUE SIZE IS 6”. THE MINIMUM DISTANCE FROM THE BOTTOM OF A COMBUSTIBLE MANTEL 
PROJECTING A MAXIMUM 3” FROM THE WALL TO THE TOP OF THE UNIT IS 12”. SEE OWNER’S 
MANUAL FOR GREATER EXTENSIONS. 
OPTIONAL FAN KIT - GZ550-KT, GD65.

CLASS :

 115V, 1.5AMP, 60HZ

L’APPAREIL DOIT EVACUER SES GAZ EN UTILISANT L’ENSEMBLE D’EVACUATION PROPRE A WOLF STEEL. REFERER 
AU MANUEL D’INSTALLATION DE PROPRIETAIRE POUR L’EVACUATION PRECISE. IL EST IMPORTANT DE BIEN 
REINSTALLER ET RESCELLER L’EVENT APRES AVOIR ASSURE LE MAINTIEN DU SYSTEME DE PRISE D’AIR.

ATTENTION : 

POUR INSTALLATION DANS UN FOYER VENTILE EN MACONNERIE. LES DIMENSIONS MINIMUMS SONT: 

HAUTER 19.75”, PROFONDEUR 13.25”, LARGEUR 29” LE DIAMETRE INTERIEUR MINIMUM DE CONDUIT D’EVACUATION 
EST DE 6”. LA DISTANCE MINIMALE, DU BAS DU MANTEAU COMBUSTIBLE FORMANT UNE PROJECTION MAXIMALE DE 
3” DU MUR AU DESSUS DE LA GARNITURE NORMALE EST 12”. REFERER AU MANUEL D’INSTALLATION POUR DES 
EXTENSIONS PLUS GRANDES. 
SOUFFLERIE OPTIONELLE  GZ550-KT, GD65.  

4500FT (0-1370m)  

  ALTITUDE/ELEVATION  

4500FT (0-1370m)

24,000 BTU/h  

INPUT/ALIMENTATION  

24,000 BTU/h

15,000 BTU/h  

REDUCED INPUT/ALIMENTATION REDUITE  

17,000 BTU/h

MANIFOLD PRESSURE:

 3.5” WATER COLUMN

PRESSION AU COLLECTEUR:

 3.5” D’UNE COLONNE D’EAU

MINIMUM SUPPLY PRESSURE:

 4.5” WATER COLUMN

PRESSION D’ALIMENTATION MINIMALE:

 4.5” D’UNE COLONNE D’EAU

MAXIMUM SUPPLY PRESSURE:

 7.0” WATER COLUMN

PERSSION D’ALIMENTATION MAXIMALE:

 7.0” D’UNE COLONNE D’EAU

AFUE:

 63.9%

MANIFOLD PRESSURE:

 10” WATER COLUMN

PRESSION AU COLLECTEUR:

 10” D’UNE COLONNE D’EAU

MINIMUM SUPPLY PRESSURE:

 11” WATER COLUMN

PRESSION D’ALIMENTATION MINIMALE:

 11” D’UNE COLONNE D’EAU

MAXIMUM SUPPLY PRESSURE:

 13” WATER COLUMN

PERSSION D’ALIMENTATION MAXIMALE:

 13” D’UNE COLONNE D’EAU 

AFUE:

 63.9%

NE PAS ALLUMER SI DES ENFANTS OU D’AUTRES INDIVIDUS À RISQUE 
SONT À PROXIMITÉ DU FOYER. APPAREIL DE CHAUFFAGE À ÉVACUATION 
DIRECTE. HOMOLOGUÉ POUR INSTALLATION DANS UNE CHAMBRE À 
COUCHER, UNE SALLE DE BAIN ET UN STUDIO. APPROPRIÉ POUR 
INSTALLATION DANS UNE MAISON MOBILE SI SON INSTALLATION EST 
CONFORME AUX EXIGENCES DE LA NORME CAN/CSA Z240MH SÉRIE DE 
MAISONS MOBILES ÉQUIPÉES AU GAZ, EN VIGUEUR AU CANADA, OU AUX 
ÉTATS-UNIS, SELON LA NORME DE SÉCURITÉ ET DE CONSTRUCTION DE 
MAISONS MANUFACTURÉES, TITRE 24 CFR, SECTION 3280. DANS LE CAS 
OÙ CETTE NORME DES ÉTATS-UNIS NE PEUT ÊTRE APPLIQUÉE, SE 
RÉFÉRER À LA NORME RELATIVE AU CRITÈRE DE MESURES DE SÉCURITÉ 
CONTRE L'INCENDIE POUR LES INSTALLATIONS DANS LES MAISONS 
MANUFACTURÉES, LES SITES ET LES COMMUNAUTÉS, ANSI/NFPA 501A.

DO NOT TURN ON IF CHILDREN OR OTHER AT RISK INDIVIDUALS 
ARE NEAR THE FIREPLACE. DIRECT VENT GAS FIREPLACE 
HEATER. SUITABLE FOR BEDROOM, BATHROOM AND BED-SITTING 
ROOM INSTALLATION. SUITABLE FOR MOBILE HOME INSTALLATION 
IF INSTALLED IN ACCORDANCE WITH THE CURRENT STANDARD 
CAN/CSA Z240MH SERIES GAS EQUIPPED MOBILE HOMES, IN 
CANADA OR IN THE UNITED STATES THE MANUFACTURED HOME 
CONTRUCTION AND SAFETY STANDARD,  TITLE 24 CFR, PART 3280. 
WHEN THIS US STANDARD IS NOT APPLICABLE USE THE 
STANDARD FOR FIRE SAFETY CRITERIA FOR MANUFACTURED 
HOME INSTALLATIONS, SITES AND COMMUNITIES, ANSI / NFPA 
501A. 

O

O THE

T

APPLIANCE THAT

HAT WIL

WILL

L COME

CO

IN

IN

N

N TH

THA

AT

T

A

A

A  SUPPLIED B

 SUP

Y THE MANU

E MANUF

FACTURER 

ACTURER

F

F

F

A   USA

SA

PL

IR3GP

IR3GP

ODEL

ODEL

SAMPLE

746 

46 

Prop

Pro

CE FOYE

CE FO
CONJ

CONJ
PO

O

REPLACE

EPLACE  / APPAREIL

 / APPAREIL À GAZ VE

 À GA

TEEL LTD.

EL LTD.

ON ROAD, BARRIE. ONTAR

N ROAD, BARRIE. ONT

IS NOT FOR USE 

S NOT FOR USE 

ASS DOORS CERTIFIED 

ASS DOORS CERTIFIED

E WITH SOLID FUEL.

H SOLID FUEL.

Z

SING THE APPROPRIATE WOLF STEEL VENT KITS

HE APPROPRIATE WOLF STEEL VENT KIT

OR VENTING SPECIFICS. PROPER REINSTALLAT

NG SPECIFICS. PROPER REINSTALL

ER SERVICING THE VENT-AIR INTAKE SYSTEM.

THE VENT-AIR INTAKE SYSTEM.

INTO A VENTED NON-COMBUSTIBLE FIREPLAC

NON-COMBUSTIBLE FIREPLAC

S: HEIGHT 20.5”, DEPTH 13.25”, WIDTH 29”. THE M

HEIGHT 20.5”, DEPTH 13.25”, WIDTH 29”. THE 

MUM DISTANCE FROM THE BOTTOM OF A COMB

MUM DISTANCE FROM THE BOTTOM OF

UM 3” FROM THE WALL TO THE TOP OF THE UNIT

UM 3” FROM THE WALL TO THE TOP OF T

TER EXTENSIONS.

TER EXTENSION

T - GZ550-KT, GD65.

- GZ550-KT, GD65.

DE/ELEVATION 

DE/ELEVAT

4500FT 

4500FT

T/ALIMENTATION 

/ALIMENTATIO

2

PUT/ALIMENTATION REDUITE  

ALIMENTATION REDUIT

R COLUMN

COL

ONNE D’EAU

ONNE D’EA

ATER COLUMN

ATER COLUMN

COLONNE D’EAU

OLONNE D’EAU

.0” WATER COLUMN

ATER COLUMN

’UNE COLONNE D’EAU

LONNE D’EAU

AFUE:

AFUE:

 63.9%

 63.9%

MANIFOLD PRESSURE:

MANIFOLD P

 10” W

PRESSION AU COLLECTEU

PRESSION A
MINIMUM SUPPLY PRES

MINIMUM SUPP
PRESSION D’ALIMEN

ESSION D’ALIM

MAXIMUM SUPPLY

MUM SUPPLY

PERSSION D’AL

PERSSION D’AL
AFUE:

AFU

 63.9%

9%

MER SI DES ENFANTS OU D’AUTRES

ER SI DES ENFANTS OU D’AUTRES

OXIMITÉ DU FOYER. APPAREIL DE CHAU

MITÉ DU FOYER. APPAREIL DE CHAU

 HOMOLOGUÉ POUR INSTALLATION DANS 

LOGUÉ POUR INSTALLATION DANS 

HER, UNE SALLE DE BAIN ET UN STUDIO. APP

LLE DE BAIN ET UN STUDIO. AP

ALLATION DANS UNE MAISON MOBILE SI SO

UNE MAISON MOBILE SI SO

ONFORME AUX EXIGENCES DE LA NORME CA

NCES DE LA NORME C

MAISONS MOBILES ÉQUIPÉES AU GAZ, EN V

MAISONS MOBILES ÉQUIPÉES AU GAZ, EN V
ÉTATS-UNIS, SELON LA NORME DE SÉCUR

ÉTATS-UNIS, SELON LA NORME DE SÉCU
MAISONS MANUFACTURÉES, TITRE 24 

MAISONS MANUFACTURÉES, TITRE 24
OÙ CETTE NORME DES ÉTATS-UNIS 

OÙ CETTE NORME DES ÉTATS-UNIS
RÉFÉRER À LA NORME RELATIVE A

RÉFÉRER À LA NORME RELATIV
CONTRE L'INCENDIE POUR LES

CONTRE L'INCENDIE POUR LES
MANUFACTURÉES, LES SITES

NUFACTURÉES, LES SITE

64.2%

IR3G

Summary of Contents for IR3GN





































Reviews: