background image

W415-1707 / B / 06.04.18

EN

28

  

venting installation

For optimum performance, it is recommended that all horizontal runs have a minimum of 1/4" (6mm) rise per 

foot using flexible venting.

42.1

!

WARNING

•  Ensure to unpack all loose materials from inside the fi rebox prior to connecting the gas and electrical supply

•  If your appliance is supplied with a remote, ensure the remote receiver is in the “OFF” position prior 

to connecting the gas and electrical supply to the appliance.

•  For safe and proper operation of the appliance, follow the venting instructions exactly.

•  The appliance exhaust fl ue collar must be sealed using Mill Pac

. All exhaust and intake vent pipe joints 

must be sealed using red RTV high temp silicone sealant (W573-0002) (not supplied) or black high temp Mill 

Pac (W573-0007) (not supplied).

•  If using pipe clamps to connect rigid vent components, a minimum of 3 screws must also be used to ensure 

the connection cannot slip off.

•  Do not clamp the fl exible vent pipe.

•  Risk of fi re, explosion, or asphyxiation. Improper support of the entire venting system may allow vent to sag 

and separate. Use vent run supports and connect vent sections per installation instructions.

•  Risk of fi re, do not allow loose materials or insulation to touch the vent pipe. Remove insulation to allow for the 

installation of the attic shield and to maintain clearances to combustibles.

•  Do not fi ll the space between the vent pipe and enclosure with any type of material. Do not pack insulation 

or combustibles between ceiling fi restops. Always maintain specifi ed clearances around venting and fi restop 

systems. Install wall shields and fi restops as specifi ed. Failure to keep insulation or other materials away from 

vent pipe may cause fi re.

The vent shield is telescopic and must be adjusted to shield the first 15” (38.1cm) of vertical vent when applicable.

note:

5.0  venting installation

For vent shield installation, see “vent shield installation” section.

Power vent system available with reduced vent pipe diameter.

5.1  firestop spacer assembly

1.  Install standoffs onto the firestop spacer 

(Fig. 1)

.

2.  Install one vent shield onto the standoff on one side of the firestop spacer 

(Fig. 2)

.

3.  Install the other vent shield on the opposite side of the firestop spacer

 (Fig. 3)

.

Fig. 1

Fig. 2

Fig. 3

Type 1 (x18)

Side view

Dimples / 

Fossettes

Standoff / 

Espaceur

Firestop spacer / 

Espaceur coupe-feu

Standoff / 

Espaceur

Summary of Contents for Acies l38 Series













































































































































Reviews: