background image

NAPCO Security Group 

NAPCO Gemini C-Series Control Panel Programming Instructions--Volume 1 

Page 10 

Programming Instructions, Volume 1 

side of Quickloader, the "

ERROR CHECK REQ'D

" warning automatically appears at the keypad to warn of a possible 

panel/Quickloader mismatch.  To select "

ENABLE PROGRAMMING

" at any unlocked GEMC-FK1 Fire keypad, simply 

press 

MENU

 to enter and press 

NEXT

 to scroll through the menu selections until "

ENABLE PROGRAMMING

" appears.  

See the "

FUNCTION MENU

" section further in this manual for more details regarding the Function menu. 

 

REMOTE DOWNLOADING RULES (CONT'D) 

 

Local Connection 

Remote (Telco and TCP/IP) with no one on site to unlock 

the keypad and "Enable Programming" 

Remote (Telco and TCP/IP) with someone on site to 

unlock the keypad and "Enable Programming" 

Full Down-

load 



Error check will be performed before the operation;  



if error(s) are found and user decides to continue, the 

"

ERROR CHECK REQ'D

" will appear on keypad.  



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear.  



Unrestricted Burg or Fire changes permitted  



Account will be Locked after operation completes 



Error check will be performed before the operation;  



if error(s) are found, the download attempt will termi-

nate.  



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear. 



Burg changes allowed 



Fire changes disallowed 



Will check to ensure panel and Quickloader match 



Account will be Locked after operation completes 



Error check will be performed before the operation;  



if error(s) are found and user decides to continue, the 

"

ERROR CHECK REQ'D

" will appear on keypad.  



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear. 



Burg changes allowed 



Fire changes allowed 



Account will be Locked after operation completes 

Partial 

Download 



Unrestricted Burg or Fire changes permitted  



Error check will be performed before the operation; if 

errors are found and user decides to continue, the 

"

ERROR CHECK REQ'D

" will appear on keypad.   



Burg changes allowed 



Fire changes disallowed 



Will check to ensure panel and Quickloader match 



Error check will be performed before the operation; if 

errors are found, the download attempt will terminate.   



Unrestricted Burg or Fire changes permitted  



Error check will be performed before the operation; if 

errors are found and user decides to continue, the 

"

ERROR CHECK REQ'D

" will appear on keypad.   

Full Upload 



Unrestricted Burg or Fire changes permitted  



Account will be Locked after operation completes 



No restrictions to upload 



Account will be Locked after operation completes 



No restrictions to upload 



Account will be Locked after operation completes 

Partial 

Upload 



Unrestricted Burg or Fire changes permitted  



No restrictions to upload 



No restrictions to upload 

Smart 

Download 



Error check will be performed before the operation;  



if error(s) are found and user decides to continue, the 

"

ERROR CHECK REQ'D

" will appear on keypad.  



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear. 



Unrestricted Burg or Fire changes permitted  



Account will be Locked after operation completes 



Error check will be performed before the operation;  



if error(s) are found, the download attempt will termi-

nate.  



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear. 



Burg changes allowed 



Fire changes disallowed 



Will check to ensure panel and Quickloader match 



Account will be Locked after operation completes 



Error check will be performed before the operation;  



if error(s) are found and user decides to continue, the 

"

ERROR CHECK REQ'D

" will appear on keypad.  



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear. 



Burg changes allowed 



Fire changes allowed 



Account will be Locked after operation completes 

Smart 

Upload 



Unrestricted Burg or Fire changes permitted  



Account will be Locked after operation completes 



No restrictions to upload 



Account will be Locked after operation completes 



No restrictions to upload 



Account will be Locked after operation completes 

Verify 



No restrictions  



No restrictions  



No restrictions  

Event Log 



No restrictions  



No restrictions  



No restrictions  

Attempt to 

Clear Error 

Check Req'd 

Trouble 



Error check must find no errors, the Quickloader account 

must not be modified and the original account program-

ming must match the panel programming.  If errors are 

found, the operation will be aborted; if mismatch is found, 

the Account and Panel Mismatch dialog will appear. 



Error check must find no errors, the Quickloader account 

must not be modified and the original account program-

ming must match the panel programming.  If errors are 

found, the operation will be aborted; if mismatch is found, 

the Account and Panel Mismatch dialog will appear. 



Error check must find no errors, the Quickloader account 

must not be modified and the original account program-

ming must match the panel programming.  If errors are 

found, the operation will be aborted; if mismatch is found, 

the Account and Panel Mismatch dialog will appear. 

(Telco) 

Callback 

Establish 

Connection 



Not Applicable 



Will check to ensure panel and Quickloader match, if a 

mismatch, the Account and Panel Mismatch dialog will 

appear. 



No restrictions  

Keypad 

Establish 

Connection 



Not Applicable 



Will check to ensure panel and Quickloader match, if a 

mismatch, the Account and Panel Mismatch dialog will 

appear. 



No restrictions  

One Step 

Download 



Not Applicable 



Error check will be performed before the operation;  



if error(s) are found, the download attempt will termi-

nate.   



if error(s) are not found, the "

ERROR CHECK 

REQ'D

" will clear. 



Burg changes allowed 



Fire changes disallowed 



Will check to ensure panel and Quickloader match, 

operation will abort if mismatch occurs. 



Account will be Locked after operation completes 



Burg changes allowed 



Fire changes allowed 



Account will be Locked after operation completes 

Quick Reference Table

 

Summary of Contents for GEMINI GEMC-255





































































Reviews: