NAPCO GEMINI C Series, Programming Instructions Manual

Page: 40 / 52

NAPCO Security Group
NAPCO Gemini C - Series Control Panel Programming Instructions -- Volume 2
Page 108 Programming Instructions, Volume 2
RF RECEIVERS & SUPERVISION TIMER OPTIONS
(ADDRESS 7958 & 7705-7720)
RF/SLC RECEIVERS: Up to 4 RF/SLC Receivers may be programmed.
NOTE: This allows wireless capability to the system, of up to 255 zones.

1. Select the number of receivers (1 - 4).

2. Enter the corresponding decimal number (1 - 4) into the right - most
location. Press
U
to save.
DATA
ENTRIES
RF /SLC
RECEIVER(S)
0 None
1 1
2 2
3 3
4 4
Default Number of Receivers = 0
Number of RF/
SLC Receivers
ADDRESS 7958
0 0
DATA ENTRIES
LEFT RIGHT
blank (•) blank (•)
blank (•) 1
blank (•) 2
blank (•) 3
blank (•) 4
blank (•) 5
blank (•) 6
blank (•) 7
blank (•) 8
blank (•) 9
blank (•) 0
blank (•) B
blank (•) C
blank (•) D
blank (•) E
blank (•) F
1 blank (•)
1 1
1 2
1 3
1 4
1 5
1 6
1 7
1 8
1 9
1 0
1 B
1 C
1 D
1 E
1 F
2 blank (•)
2 1
2 2
2 3
2 4
2 5
DELAY
0 min.
10 min.
20 min.
30 min.
40 min.
50 min.
60 min.
70 min.
80 min.
90 min.
100 min.
110 min.
120 min.
130 min.
140 min.
150 min.
160 min.
170 min.
180 min.
190 min.
200 min.
210 min.
220 min.
230 min.
240 min.
250 min.
260 min.
270 min.
280 min.
290 min.
300 min.
310 min.
320 min.
330 min.
340 min.
350 min.
360 min.
370 min.
RF SUPERVISION TIMERS
DATA ENTRIES
LEFT RIGHT
2 6
2 7
2 8
2 9
2 0
2 B
2 C
2 D
2 E
2 F
3 blank (•)
3 1
3 2
3 3
3 4
3 5
3 6
3 7
3 8
3 9
3 0
3 B
3 C
3 D
3 E
3 F
4 blank (•)
4 1
4 2
4 3
4 4
4 5
4 6
F F
DELAY
380min.
390 min.
400 min.
410 min.
420 min.
430 min.
440 min.
450 min.
460 min.
470 min.
480 min.
490 min.
500 min.
510 min.
520 min.
530 min.
540 min.
550 min.
560 min.
570 min.
580 min.
590 min.
600 min.
610 min.
620 min.
630 min.
640 min.
650 min.
660 min.
670 min.
680 min.
690 min.
700 min.
2550 min. = 42
Hr., 30 min.
RF SUPERVISION TIMERS: RF Supervision Timers may be
programmed for each type of transmitter used. A transmitter will
send a transmission every time it is tripped, when there is NO
activity, the transmitter sends a status transmission about once
an hour. If the receiver does NOT receive ANY signal (a trip or a
status) from a transmitter in the time specified for transmitter
type, a system trouble "
E-04-NNN
" will be displayed at the
keypad.
1. Select timer delay from the table shown. Timers are
programmed in increments of 10 minutes each.
Valid entries are: (•) 8 - FF (80 minutes - 2550 minutes)
(Note that 2550 minutes = 42 hours, 30 minutes).
WARNING: Timers have uncertainty of +/ - 30 minutes.
2. Enter in corresponding address locations above (left and
right digits).
3. For a desired timer not listed, do the following:
A. Choose a desired timer (intervals of 10).
(example: 1440 minutes = 24 Hours)
B. Divide by 10.
(example: 1440 ÷ 10 = 144)
C. Divide by 16.
6 Quotient Left Digit
16 100
96
4 Remainder Right Digit
NOTE: These timers apply only to Supervised RF
Transmitters (see RF Transmitters in Easy Menu
Driven Mode Programming).
[Default = blank (•) 8 from address 7705 - 7712 (80 minutes)]
RF SUPERVISION
TIMER
ADDRESS 7705 - 7712
RF TRANSMITTER
LEFT ADDR RIGHT
Type 0 Window/Door, 2 Pt. 7705
Type 1 Window/Door, 2 Pt. 7706
Type 2 Window/Door, 2 Pt.
7707
Type 3 Window/Door, 2 Pt.
7708
Type 4 Window/Door, 4 Pt. 7709
Type 5 PIR
7710
Type 6 PIR 7711
Type 7 Smoke Detector
7712
[Default = blank (•) 8 from address 7713 - 7720 (80 minutes)]
RF SUPERVISION
TIMER
ADDRESS 7713 - 7720
RF TRANSMITTER
LEFT ADDR RIGHT
Type 8 Smoke Detector 7713
Type 9 Keyfob
7714
Type A Dual Tech.
7715
Type B Keyfob 7716
Type C Window/Door, 4 Pt.
7717
Type D PIR 7718
Type E Smoke Detector
7719
Type F Napco Glass Break
7720
RF SUPERVISION TIMERS