background image

791-9006 2  08/19/18

OPERATING MANUAL FOR 791-9006

WARNING INFORMATION

This is the safety alert symbol. It is used to alert you 
to potential personal injury hazards. Obey all safety 
messages that follow this symbol to avoid possible 
injury or death.

 

   

IMPORTANT: READ THESE INSTRUCTIONS BEFORE OPERATING

BEFORE USING THIS DEVICE, READ THIS MANUAL COMPLETELY AND THOROUGHLY, UNDERSTAND ITS OPERATING 
PROCEDURES, SAFETY WARNINGS AND MAINTENANCE REQUIREMENTS.

It is the responsibility of the owner to make sure all personnel read this manual prior to using the device. It is also the responsibility of 
the device owner to keep this manual intact and in a convenient location for all to see and read. If the manual or product labels are lost 
or not legible, contact NAPA for replacements. If the operator is not fluent in English, the product and safety instructions shall be read to 
and discussed with the operator in the operator's native language by the purchaser/owner or his designee, making sure that the operator 
comprehends its contents.

THE NATURE OF HAZARDOUS SITUATIONS

The use of portable automotive lifting devices is subject to certain hazards that cannot be prevented by mechanical means, but only by the 
exercise of intelligence, care and common sense.  It is therefore essential to have owners and personnel involved in the use and operation of 
the equipment who are careful, competent, trained and qualified in the safe operation of the equipment and its proper use. Examples of haz-
ards are dropping, tipping or slipping of loads caused primarily by improperly securing loads, overloading, off-centered loads, use on other 
than hard level surfaces, and using equipment for a purpose for which it was not designed.

METHODS TO AVOID HAZARDOUS SITUATIONS

    •  Read, study, understand and follow all instructions before operating this device.

    •  Inspect the jack before each use. Do not use jack if damaged, altered, modified, in poor condition, leaking hydraulic fluid,  

 

 

    or unstable due to loose or missing components. Make corrections before using.

    •  Consult the vehicle manufacturer for the transmission's center of balance.

    •  Never use a power tool to activate the saddle tilt screws. Operate by hand or socket wrench.

    •  Secure the transmission to the jack's saddle with the anchorage restraint system provided before raising or lowering 

      the transmission.

    •  Center load on saddle. Be sure setup is stable before working on vehicle.

    •  Support the engine with a stand before unbolting the transmission from the engine.

    •  Wear eye protection that meets ANSI Z87.1 and OSHA standards (users and bystanders).

    •  Do not use jack beyond its rated capacity. Do not shock load.

  •  

Do not crawl under engine or place any part of your body under engine at any time.

    •  Use only on a hard level surface.

    •  Adequately support the vehicle before starting repairs. 

    •  Use of this product is limited to the removal, installation and transportation in the lowered position, of transmissions,   

 

 

    transfer cases and transaxles.

    •  Do not use any adapters unless approved or supplied by NAPA.

    •  Do not use (or modify) this product for any other purpose than that for which it was designed without consulting the    

 

 

    manufacturer's  authorized representative.

    •  Always lower the jack slowly and carefully.

    •  Failure to heed these warnings may result in serious or fatal personal injury and/or property damage.

 

WARNING:

 This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer and  

 

 

birth defects or other reproductive harm.  For more information go to www.P65Warnings.ca.gov.

CONSEQUENCES OF NOT AVOIDING HAZARDOUS SITUATIONS

Failure to read this manual completely and thoroughly, failure to understand its OPERATING INSTRUCTIONS, SAFETY WARNINGS,
MAINTENANCE INSTRUCTIONS and comply with them, and failure to comply with the METHODS TO AVOID HAZARDOUS SITUATIONS
could cause accidents resulting in serious or fatal personal injury and/or property damage.

WARNING: Indicates a hazardous situation 
which, if not avoided, could result in death 
or serious injury.

WARNING

WARNING

WARNING

WARNING

Summary of Contents for Carlyle Tools 791-9006




















Reviews: