background image

Installation Guide Modbus E5000 IAQ probe 

 

page 8/8 

12. Disconnection 

 

 

 

13. Recommendations 

The EP50000 probe guarantees you precise measurements for years to come, provided you give it some 
attention ... 

 

Do not install your probe near sources of alcohol, gasoline, fuel oil, lubricants, paint or chemicals. 

The VOC sensor would be contaminated. 

 

Do not spill aerosol products such as deodorants, perfumes, paints, lubricants, etc. near the probe. 

 

Avoid contact or proximity with silicone-based materials. 

 

Do not use detergent or solvent to clean the probe, chemicals can cause sensor failure by 

contaminating or damaging it temporarily or permanently. 

 

Do not immerse or spray any liquid in the openings, this could permanently damage the probe. 

 

Do not attempt to expect an accurate VOC measurement immediately after exposure to high 

concentration, the sensor requires time to recover and perform to its full potential. 

 

14. Warranty 

 
This probe was manufactured to high quality standards. However, it can happen that it presents a defect 
or a failure despite the numerous tests to which it has been subjected. This device is guaranteed against 
any manufacturing or material defect within the limits of the following provisions: 

 

The warranty is strictly limited to the exchange or repair in the factory of parts recognized as 

defective, after examination and control, to the exclusion of any other compensation. 

 

The warranty period, offered by the manufacturer, is one year and begins to run from the date of 

purchase. 

 

It is only effective if the device has been used in accordance with the installation instructions, 

recommendations and good practice. 

 

Are excluded from the guarantee: 

-

 

Damage resulting from abnormal conditions of use. 

-

 

Damage caused by shocks or excessive mechanical forces, 

-

 

Damage or accidents resulting from negligence or resulting from a transformation or - 

transformation attempted of the device. 

-

 

Damage due to disassembly and improper reassembly of the probe. 

 

The warranty is only valid for devices that are returned to the manufacturer's address. 

 

Interventions under the guarantee cannot have the effect of extending the duration of the 

guarantee. 

 

The provisions of this guarantee are not exclusive of the benefit, for the benefit of the purchaser, 

of the legal guarantee for defects and latent defects which applies in any event. 

Summary of Contents for LoRa EP5000L









Reviews: