background image

6

Safety information

Safety 
symbols

The symbols used in the ADAM-MC and the manual are 
explained below:

The Caution symbol denotes a risk of safety 
hazard.  

ON (Power)

Protective earth (Ground)

The CE mark symbolizes that the product conforms 
to all  applicable European Community provisions 
for which this marking  is required. Operation of the 
ADAM automated cell counter is subject to the  
conditions described in this manual.  
The protection provided by the device may be 
impaired if  the instrument is used in a manner 
not specified by the manufacturer. 

Caution, Biohazard
Protective measures must be used in dealing 
with biologically hazardous materials such as 
carcinogenic reagents.

Disposal of your old appliance
1. When this crossed-out wheeled bin symbol 
    is attached to a product, it means the product 
    is covered by the European Directive 2012/19/EU.
2. All electrical and electronic products should 
    be disposed of separately from the municipal
    waste stream via designated collection facilities
    appointed by the government or the local 
    authorities.
3. The correct disposal of your old appliance
    will help prevent potential negative consequences
     for the environment and human health.
4. For more detailed information about disposal 
    of your old appliance, please contact your city 
    office, waste disposal service or visit our
    web-site,

Meaning

Symbol

www.nanoentek.com.

Summary of Contents for ADAM-MC









































Reviews: