![background image](http://html1.mh-extra.com/html/namco/air-combat/air-combat_operators-manual_3158425005.webp)
2-2 Caution When Handling
a.
AC
power must always be turned OFF, and the game unplugged, before
replacing any parts or connecting/disconnecting connectors.
b . When unplugging the game from an
outlet, always grasp the plug,
not the cord.
c. Do not subject game to physical shock when transporting or moving it.
d . The power supply range is between 1
(switchable to 220 VAC).
e. The cabinet must be grounded with a securely connected ground plug.
f.
Care must be taken at all times to avoid electrical shock whenever inspecting
or adjusting the game, particularly around the monitor.
g. Always return the leg levelers to the extreme “up” position before moving the
game, and separate the
game
into its two assemblies monitor cabinet and
seat.
h . Adjustment is required whenever the game PC board, ROM, Joystick, Throttle
Control or other potentiometers are changed.
i.
DO NOT attempt to repair the Printed Circuit Board (PCB). It contains
sensitive chips that could easily be damaged by even the small internal voltage
of a multi-meter. Always return
the
PCB to your distributor for any repairs.
2-3
Caution When Handling Rear Projection Screen
The rear projection screen is easily damaged, or deformed, unless proper care is
given to it’s care and cleaning.
a.
The screen should generally be cleaned by wiping gently with a soft cloth.
b . If extremely dirty, wet a cloth with a mild solution of neutral detergent and
water, wring dry, and wipe gently. Finish with a soft dry cloth.
c. Never:
l
Use any chemical cleaners like paint thinner, benzine etc.
l
Use any alkaline or acid based detergent.
l
Apply any volatile matter such as insecticide.
.
Leave the screen in contact with rubber or vinyl products for any extended
time.
3. INSPECTION
The AIR COMBAT Game cartons should be carefully inspected upon receipt to
insure that the game is complete and was delivered in good condition.
Inspect
the game
cabinet by doing the following:
Examine the monitor cabinet exterior and seat assembly for dents, chips, or
broken
parts.
2 .
Open the side service door and the coin door
on
the seat assembly as
the
back cover of the monitor cabinet, and
inspect the interior
as follows:
2
Summary of Contents for Air Combat
