![background image](http://html1.mh-extra.com/html/namco/air-combat/air-combat_operators-manual_3158425036.webp)
c. On an unstable surface or floor subject to vibration.
d . Against a wall that would restrict air circulation.
Handling Precautions
a.
Do not subject game to physical shock when transporting or moving it.
b .
The cabinet should be grounded with a securely connected ground line.
c. The game includes areas of high-voltage. Care should be taken at all times to
avoid electrical shock whenever inspecting or adjusting it.
d . Power must always be turned off before replacing any parts.
e. When unplugging the game from an electrical outlet, always grasp the plug,
not the cord.
f. DO NOT attempt to repair the Printed Circuit Board
on site. It contains
sensitive integrated circuit chips that could easily be damaged by even the
small internal voltage’of a multi-meter. Always return the PCB to your dis-
tributor for any repairs.
g. Exercise caution to prevent damaging crab figures or track mechanism.
2 - 2
3. UNPACKING
CRACKY
is shipped in a single carton, with the Main Cabinet (base) on a floor
tray, and the Marquee Cabinet in a separate box in front of it. To unpack:
1 . Remove Marquee Cabinet box from shipping container and set it aside.
2 . Roll the Main (base) Cabinet off the shipping carton base on its casters.
4. INSPECTION
After the two CRACKY
assemblies are removed from their shipping boxes,
carefully inspect them to insure that the game is complete and was delivered in good
condition by doing the following:
1 . Examine the main cabinet exterior for dents, cracks, or broken parts.
2 . Inspect the marquee cabinet for dents, cracks, or broken parts -particularly the
acrylic display panel.
3 . Open the rear doors of both cabinets and;
a. Verify that all plug-in connectors (on the cabinet harness) are firmly
plugged in, DO NOT force connectors together. The connectors are
labeled to assure the proper orientation. A reversed edge connector can
damage a PCB and will void your warranty.
b . Inspect the power cord to insure that there are no insulation cuts or dents.
c. Inspect the power supply connectors.
d . Inspect all other major sub-assemblies, to make sure that they are mounted
securely and that all ground wires are
connected.
2
Summary of Contents for Air Combat
