Page 4
No part of this publication may be reproduced by any mechanical, photographic or electronic process, or in the form of
phonographic recording, nor may it be stored in a retrieval system, transmitted or otherwise copied for private use, without
permission from
NAMCO EUROPE LIMITED.
While the information contained in this manual is given in good faith and was accurate at the time of printing,
NAMCO EUROPE LIMITED reserve the right to make changes and alterations without notice.
This equipment has been manufactured in accordance with European Directives, and has been tested and complies with the
directives 89/336/EEC and 72/23/EEC by the application of EN55014-1, EN55014-2 and EN60335-2-82 standards and as such
bears the CE marking. Any changes or modifications to this equipment must be in accordance with the European Directives.
Any unauthorised changes to this equipment may contravene such directives.
Under some conditions of extreme external interference, e.g. radio transmissions, electrostatic discharge or mains born
transients, some degradation of performance may occur. However the equipment will recover normal performance once the
source of interference has ceased or been removed.
If the game processor resets due to an interruption of the mains voltage, any credits established will be lost.
This equipment is not a machine as defined by the machinery directive 89/392/EEC.
SAFETY WARNING
In order to use this equipment safely, be sure to read this Operators Manual carefully before installation, adjustment or use of
this equipment.
Whenever the owner of this equipment entrusts dis-assembly, installation, adjustment or routine maintenance to another
person, the owner should ensure that that person read the appropriate precautions and relevant sections of this manual before
starting work.
In order that no accidents occur when the equipment is in operation, strictly follow the notes on safety as described
below.
This manual along with the Installation Manual (where applicable) form an integral part of the equipment and must be available
to the operating or service personnel at all times.
This equipment is for indoor use only and should only be used for the purpose intended.
Namco Europe Ltd. bears no responsibility for accidents, injury or damage resulting from unauthorized changes to, or improper
use of this equipment.
SAFETY NOTES
The following safety notes are used throughout this manual. Familiarize yourself with each of these notes and it’s meaning
before installing, servicing or making adjustments to this equipment.
WARNING
l
l
l
l
l
Warning denotes a hazard that could result in injury or death. Do not proceed beyond a warning note until
the indicated conditions are fully understood and met.
CAUTION
i
Caution denotes a hazard that could result in damage to the equipment. Do not proceed beyond a caution
note until the indicated conditions are fully understood and met.
GENERAL SAFETY CONSIDERATIONS
l
l
l
l
l
Only operate this equipment after checking that it has been installed correctly and in accordance with this
manual.
l
l
l
l
l
The warning notices must always be kept in good condition and replaced if worn, so that customers can read
them clearly.
l
l
l
l
l
If there is an error or problem with the machine, operation must be stopped immediately and the problem
rectified before any further use.
l
l
l
l
l
Installation, service, adjustment or routine maintenance should be carried out by suitably qualified persons only.
l
l
l
l
l
For continued protection against fire hazard, replace fuses with the same type and rating. The use of other fuses
or material is prohibited.
l
l
l
l
l
The power supply inside the monitor will remain hot and have areas of high voltage even though the equipment
has been tuned OFF, and there is the possibility of burns or electric shock. Be careful not to touch these areas.
l
l
l
l
l
To prevent possible electric shock due to failure, this equipment MUST be fitted with a securely connected
EARTHED plug.
l
l
l
l
l
If at any time the mains lead becomes damaged, it must be replaced immediately.
l
l
l
l
l
Do not turn the power switch ON until the equipment has ben installed correctly.
i
Before connecting the machine to the mains supply, ensure that the equipment is set for the correct voltage and that the
correct fuses are fitted.
