background image

24

12

14

Loosen

Grindstone

Collet Nut

Latch

Latch

Groove

Collet

Collet Nut

Collet Nut

DOWN

Collet

Wrench Seat

Fig. 3

Fig. 4

Fig. 5

Fig. 6

REPLACING THE COLLET

8.

When installing the collet into the collet nut, be sure to fully engage the latch inside the 

collet nut to the groove on the collets outer diameter area. It is very important to note that 

if the collet is attached without being engaged with the latch of the collet nut, the collet will 

stick inside the spindle taper, and this may cause damage to the collet and or the spindle. 

   CAUTION

Remove the grindstone according to the section " 7. REPLACING THE GRINDSTONE " 
procedure above and remove collet nut assembly (Fig. 3).

The collet and collet nut are secured by a groove in the collet and a flange in the collet nut. To 
remove the collet hold the collet nut in one hand and push diagonally down on the collet. The 
collet should be released (Fig. 4).

To install the collet, hold the collet at a slight angle, and insert it into the collet nut (Fig. 5).
Press the collet in the collet nut by positioning the collet in the collet nut and pressing down on flat 
surface (Fig. 4).
Be sure to fully engage the latch inside the collet nut into the groove on the collet's outer 
circumference area (Fig. 6). 

OM-K0679_PLANET600_(A5x)_EN_170710発注先変更準備(住所変更).indd   24

2017/07/18   13:55:34

Summary of Contents for PLANET600 Series





















Reviews: