background image

Connection block 

 

 

 
1

 – Phono Inputs 

 

1 – Input A, comes with an MC (Moving coil) module as standard. 

 

 2 

– 

A

 module ground connector. 

 

3 – Input B, for MM or MC optional module. 

 4 

– 

B

 module ground connector. 

 

2 – Outpout group 

 

5 – RCA outputs. 

 

6 – XLR outputs

*

 

7 – Low level (Lo) or high level (Hi) output switch. 

 

8 – LEMO mains connector. 

 

3 – Device identification plate 

 

9 – Serial number. 

 

*The XLR outputs are provided to make your VPS easier to connect to your Hi-

End system. These outputs reproduce the RCA output signal on XLR connectors. 

They are unbalanced. 
 

Make sure you are using the shortest possible cable (with no loops or useless 

bends) between your turntable and VPS. 

 
The RCA or XLR outputs can equally be used for connection to a PL-L or PL-P. 

 

NB

 Caution: Do not use the XLR and RCA outputs simultaneously. 

 

In order to obtain optimal performances from the Nagra VPS, it is preferable to 

leave the device switched on for about 30 minutes before use, so that the internal 

components can reach their optimum operating temperature. 

 

Like all tube electronic devices, the Nagra VPS needs a running-in period. It will 

reach peak performance after a few hours of use. 

 

 

 

 

 

8

 

 

Nagra – 

VPS 

 

 

Summary of Contents for VPS




















Reviews: