background image

TY-GC31-004A 

13/24 

 

 

 

Rev.B 

6. Noise prevention 

 

 

Power line

 

 

If noise remains in the power line, it may cause malfunctions such as fluctuation of display.

 

Take 

care not to tangle the AD/DC power line. Also, use a stable power source that has high noise 
rejection ratio and will not cause ripple voltage.

 

 

 

 

 

Output routing

 

 

In the open collector output circuit, since output line and internal circuit are connected directly, 
pay attention not to tangle lines. Also, make connection cables as short as possible. 

 

 

 

 

 

Induction noise

 

 

Induction noise from outside sources may cause malfunctions.

 

In this case, separate the device 

from the noise source, change direction, and use a magnetic shield or an electrostatic shield. 

 

 

 

 

 

Lightning surge

 

 

Lightning surge may cause malfunctions.

 

Please connect this unit to indoor distribution network 

which is free from influence of lightning surge.

 

 

 
Noise issues are complicated and many of them cannot be solved easily. 

 

If measured values 

often fluctuate or differ, they may be affected by noise 

 

In this case, take noise prevention 

measures described above.

 

 

 

7. Storage location 

 
 

Do not store this device in the following places as it may cause malfunction and 
damage. 

  Any place that water can reach. 

  Any place where there can be negative influence of atmosphere, temperature, 

humidity, sunlight, dust, salt or sulphuric air. 

  Any places where there is vibration or shock (including during transportation). 

  Any place where chemicals are stored or where there are releases of gas. 

  In direct sunlight or inside a hot vehicle. 

 

8. Maintenance 

 
In this unit, there are no moving parts in the sensing element and circuit components so 
basically there will be no maladjustment. However, depending on the use condition, aging may 
occur so biannual regular check is recommended.

 

For the zero point adjustment, perform it 

following the instructions of zero point adjustment herein.

 

 

Since plastic molding material is used for the case part of this device, make sure not to touch it 
with soldering iron, etc.

 

 

Also, chemicals may have an adverse effect on the case so ensure 

that none come in contact.

 

 

Caution

 

 

Summary of Contents for GC31


























Reviews: