background image

TY-GC31-004A 

23/24 

 

 

 

Rev.B 

 Error  display 

An error message and pressure value are alternately displayed when one of the following 
errors occurs in the measurement mode (In case of "Out of pressure display range" error, only 
error message is displayed). Check the content of error message and take the action below 
immediately. 
 

Error 

display 

Contents Actions 

 

Out of pressure display range (Upper limit) 

A pressure above 110% F.S. of pressure 
range is applied, or when indicated value 
exceeds 1999. 

Adjust the applied pressure within 
the rated pressure. 

 

Out of pressure display range (Lower limit) 

A pressure less than -10% F.S. of pressure 
range is applied, or when indicated value 
falls below -1999. 

 

During zero point adjustment, applied 
pressure is outside the range of ±10% F.S. 

Open the unit to the atmosphere 
and perform zero point adjustment   
again. 

 

Comparator 1 is overloaded 

Drop the load current below 80mA 
before use. 
To recover from error status, turn 
on the power again. 

 

Comparator 2 is overloaded 

 

Comparator 1 & 2 are overloaded 

 
 

 Backup of setting values 

The unit has an internal EEPROM and settings and the key lock state are maintained even 
after the power is turned OFF. However, peak / bottom values are not maintained. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for GC31


























Reviews: