background image

4

a. Instrument Connection (using the WGT instrument transmitter)

Insert an audio cord with a ¼” mono phone plug in the 

AF OUTPUT JACK (8)

 on the rear panel of 

the receiver. Plug the other end of the cord into amplifier, effect or mixing board. Adjust the 

VOLUME CONTROL (6)

 on the 401X QUAD clockwise to about ¾ rotation until the volume level is 

comfortable for your application. This setting is roughly equivalent to direct instrument cord 

connection. Turning the volume up to maximum will provide 4dB gain over a cord.

b. Microphone Connection (using the WLT transmitter with either a headset 

or lavalier microphone or the WHT handheld microphone transmitter)

Insert an audio cord with a ¼” mono phone plug in the 

AF OUTPUT JACK (8)

 on the rear panel of 

the receiver. Plug the other end of the cord into amplifier, effect or mixing board. Adjust the 

VOLUME CONTROL (6)

 on the 401X QUAD clockwise to about ½ MAX and adjust the volume 

control until the volume level is optimal. If the volume control is set too high, you may overload 

your mixer or amp.

Since your 401X QUAD is comprised of four separate and independent XLR output channels, it 

can be used with either one, two, three or four channels operating. Simply turn your mixer volume 

control of any channel which you are not using to minimum. If the mix line out is used, just turn 

down the 401X QUAD receiver’s volume controls.

16V AC/DC Adapter

Antennas

5

8

9

10

11

3

6

4

7

opeRaTIon

Summary of Contents for 401X Quad













Reviews: