background image

NAD

32

NAD ELECTRONICS LTD

LONDON

© 1995. AV 713 I.M. PRINTED IN MALAYSIA

Power Amplifier Section
Power  Output into 8Ω
Stereo Mode

60 W (14 dBW)

(Min. power per channel, 20Hz-20kHz, 
both channels driven, with no more 
than rated distortion)
Front L/R and Center Channels

50W 

Rear Channels 

15W

Dynamic power output (Front) 8 ohms:

70W (18 dBW)

4 ohms:

110W (19 dBW)

Continuous Power output

8 ohms:

60W 

4 ohms:

60W

THD 

20Hz-20kHz              

0.08 % (Front)

IM distortion

0.08% (Front)

Damping factor

60 at 8Ω (Front)

Input sensitivity and Impedance:

Phono:

2.5mV

Line:

150mV, 2.2k ohms

Video:

1Vp-p, 2.2k ohms

Output level and Impedance

Output:

150mV, 2.2k ohms

Pre Out: 1V, 2.2k ohms 

(Subwoofer)

Video:

1Vp-p, 75 ohms

Phono Oveload  1kHz, 0.5% THD

120mV RMS

Frequency response  5Hz to 50kHz

±0.8dB

RIAA Deviation  20Hz- 20kHz

±0.8dB

Tone control

Bass:

±10dB at 100Hz

Treble:

±10dB at 10Hz

Signal/Noise ratio, A weighted

Phono: 80dB
CD/Tape: 100dB

Muting:

-40dB

FM Tuner Section
Usable Sensitivity   

Mono:

11.2dBf, 1.0µV

75 ohms IHF

Stereo:

17.2 dBf, 2.0 µV 

50dB Quieting Sensitivity  

Mono:

18.2 dBf, 2.2µV

75 Ω

Stereo:

38.2 dBf, 22µV

Capture ratio

90dB

Signal to Noise Ratio (IHF)

Mono:

73dB

Stereo:

67dB

Alternate channel attenuation Mono:

55dB (IHF)

Selectivity DIN ±300kHz, 40kHz Devi.

50dB

AM Suppresion ratio

50dB

THD

Mono:

0.15%

Stereo:

0.25%

Frequency Response  30-15kHz

±1.5dB

Stereo Separation

45dB at 1kHz
30dB at 100-10kHz

AM Tuner Section
Usable Sensitivity  

30µV

Image rejection ratio

40dB

IF rejection ratio

40dB

Signal to Noise ratio (IHF)

40dB

THD

0.7%

Remote Control
Power, Master Volume Up/Down, Mute, Sleep, Surround Mode,
Delay Time, Test Tone, Center Volume Up/Down, Rear Volume
Up/ Down, Input Selector (CD, Phono, Tuner, Tape 1, Tape 2,
Video 1, Video 2)
Deck A/B: (Play, Reverse Play, Stop, Record/Pause, Fast
Forward, Rewind)
CD: (Play, Pause, Stop, Disc, Skip Forward/Back)
Tuner: (Bank, Preset Up/Down) 

Physical Specification
Dimensions in mm (W x H x D)

435 x 145 x 330

Net weight

9.3kg

Shipping weight

10.5kg

SPECIFICATION - NAD AV 713 SURROUND SOUND RECEIVER

Summary of Contents for 713

















Reviews: