Nabtesco GM Series Operation Manual Download Page 7 | Manualshive

Page: 7 / 31

Nabtesco GM Series Operation Manual Download Page 7

GM Series

TM19040 P.7/31

1.2. Types of Warnings and their Meanings

The following four types of warnings are used according to the expected hazards during operation and
maintenance of the product. Neglecting such safety rules and warnings may cause accidents, resulting in
serious injury and/or damage to this product.

Signal word

Meaning

DANGER

Indicates an imminently hazardous situation which, if not avoided or prepared
protection measures, will result in death or serious injury.

WARNING

Indicates a potential hazardous situation which, if not avoided or prepared
protection measures, could result in death or serious injury.

CAUTION

Indicates a potential hazardous situation which, if not avoided or prepared
protection measures, may result in minor or moderate injury.

NOTICE

Indicates a potential hazardous situation which, if not avoided or not prepared
protection measures, may result in property damage.

1.3. Notation and Meaning of Important Information

Notation

Meaning

NOTE

Important maters or useful information for the GM operation, maintenance and
inspection.

«
...
5
6
7
8
9
...
»

Summary of Contents for GM Series
































Reviews:

No comments