manualshive.com logo in svg

Nabtesco GM Series, Operation Manual

Share
Download
Nabtesco GM Series Operation Manual Download Page 22

 

 

   

GM Series   

 

TM19040 P.22/31

 

 

 

 

 

z

 

Replacement procedure 

Replace  and  replenish  according  to  hydraulic  oil  replacement  and  replenishment  procedure  of  the 
machine. 

  NOTICE

 

Use the same hydraulic oil brand for replacement and replenishment, and do not mix different 
brands.

 

 

5.4.  Type of Lubricant and Filling volume 

  NOTICE

 

Use the lubricant recommended by us. Use of any other lubricant may degrade the performance 
and durability of GM. 

 

z

 

Lubricant specified by Nabtesco

 

Use a lubricant with extreme-pressure additive equipment to SAE # 90 (API class GL-4 or higher).The 
following brands are recommended.

 

 

Manufacturer name 

Product name 

JXTG Nippon Oil &Energy 

Gear Oil GL-4 90 

Idemitsu Kosan 

Apolloil Gear

 

HE90 

Exxon Mobil 

Mobilube

 

HD80W-90 

Shell 

Shell Spirax EP90 

Cosmo Oil 

Cosmo Gear GL-4 90 

 

z

 

Filling volume lubricant

 

Prepare lubricant according to the amount of lubricant in the confirmation notice.

 

 

z

 

Temperature range of lubricant

 

Operating temperature range : -20 

～

80 [

℃

] 

 

 

 

 

Summary of Contents for GM Series
































Reviews:

No comments

Brands by name

Popular brands

Load more brands