background image

ElectricalInstallationManualU-30“D”Control

www.NabcoEntrances.com

Part #C-00121 

Rev. 8-25-16

iv 

GENERAL SAFETY RECOMMENDATIONS

Do not install, operate or service this product unless you have read and understand 

the General Safety Recommendations, Warning Labels, contained in this manual. 

Failure to do so may result in bodily injury, or property damage.

Read, study and understand the installation and operating instructions contained in, 

or referenced in this manual before operating. If you do not understand the instruction, 

ask a qualified technician. Failure to do so may result in 

bodily injury, or property 

damage and will nullify all warranties.

Disconnect all power to the junction box prior to making any electrical connections. 

Failure to do so may result in seriouc personal or fatal injury. When uncertain whether 

power supply is disconnected, always verify using a voltmeter.

Do not place finger or uninsulated tools inside the electrical controller. Touching wires 

or other parts inside the enclosure may cause electrical shock, serious injury or death. 

The Ground wire from the Magnum IV Control 120 VAC Harness, and the Incoming 120 

VAC Ground wire must be connected to the Ground screw located within the Swing 

door Header.

If the door appears broken or does not seem to work correctly, it should be 

immediately removed from service until repairs can be carried out or a qualified 

service technician is contacted for corrective action.

Notice:    This manual, the owner’s manual and all other associated manuals must be given to and 

retained by the purchasing facility or end user.

Notice:    Wiring must meet all local, state, federal or other governing agency codes.

Notice:    All electrical troublshooting or service must be performed by qualified 

 

electrical technicians and must comply with all applicable governing  

agency codes.

Note:       All Adjustments must be made with a small screwdriver. Do Not use a pencil.
Note:       Do Not take shortcuts.

WARNING

WARNING

WARNING

DANGER

DANGER

CAUTION

CAUTION

Summary of Contents for GYRO TECH GT-1175


































Reviews: