Mystere ca11 User Manual Download Page 4

ca11  

Warning - Initial setup

To prevent serious injury, electrical shock or fire:

•   Do not operate with bottom plate removed.

•   Keep away from rain and moisture.

•   Disconnect all cable connections before changing fuses and/or tubes.

•   Do not replace tubes without reading instructions.

•   Do not replace fuses or tubes if you have any doubt about your ability to 

do so. We accept no responsibility for any personal or material damage 

due to incompetent use or users.

•   Remove the 

Mystère

 ca11 from its packaging. Use the white gloves.

•   Remove tube cage. Carefully pull it up and away from the preamplifier.

•   Remove the protective foam surrounding the tubes.

•   Check that each tube is firmly seated in its socket. Use gloves.

•   Replace cage back in its place if desired.

•   Check to see the power switch is off (down).

•   Connect each source to the corresponding plugs.

•   Connect output of preamp with input of poweramp.

•   Your 

Mystère

 preamp inverts phase. Connect positive (+) to positive and 

negative (-) to negative at your poweramp, then positive to negative, and 

negative to positive at your speaker. Do so for both speakers.

•   Plug powercords into pre- and power amplifier, then into wall sockets.

•   Switch the preamplifier on and wait for 30-60 seconds to warm up.

•   Switch the poweramplifier on after the preamplifier has been on for 30-

60 seconds.

•   The tubes will be warmed up and ready to use in about 30 seconds.

Mystère

Contents

1x  Mystère ca11

  

Preamplifier 

1x  Power Cord

1x  Owner’s Manual

1x  White Gloves

Tubes  4x 6SN7
  

 

1x 5AR4

Fuses  Littelfuse Series 218 or 219
  

 

1 x 0,63AT (100-120VAC)

  

 

1 x 0,315AT (200-240VAC)

Warning

Do not replace fuses with any 
fuse other than the same type 
and rating as used by the factory.

Summary of Contents for ca11











Reviews: