background image

Step 1 

(A) Determine supply and return pipe location for your size radiator.

Step 2 

(B) Place the hangers in the center of the mounting bracket

 NOTE: 

The hanger needs to be in the center of the bracket to allow for variance.

 NOTE:

 Install the plastic inserts on the hangers.

 NOTE: 

(C) The radiators must be a minimum of 4” off the floor.

Step 3

  (D) Measure the distance from the bottom of the radiator to the hanger and add 4” for step 3.

Step 4

  (E) Measure the distance from the bottom of the radiator to the top hanger and add 4” for step 3.

Step 5

  (F) Measure the distance from the center of the supply or return pipe to the center of the hanger.

 NOTE: 

Use a level to mark the hanger locations on the wall.

 NOTE: 

Attach the hangers with suitable hardware. Adequate blocking is recommended to

 

support the weight of the radiators.

Many MYSON products are in excess of 70 pounds. Care should be taken to have help to lift larger 
radiators into place to avoid lifting injuries. 

12

Décor Radiator Series

Conventional Wall Installation-Radiator

MYSON

Mounting 
Bracket

B

Hanger

F

F

F

E

D

C

A

E

D

C

A

Summary of Contents for H11 10

















Reviews: