11
1. WARNINGS AND GENERAL SAFETY INSTRUCTIONS
This manual contains important safety information.
An incorrect installation or an improper use may cause serious damages to persons or objects.
Read this manual carefully and completely. Pay particular attention to the sections marked by the symbol:
This indicates that risk to personal injury may occur if not adhered to. Store this manual safety for future use.
Always disconnect main power supply before operating in the automatic gate.
Make sure that the earth system is perfectly working and always connect the automatic gate to it.
The installation of automatic gates and doors must fully comply with the requirements set forth in 2006/42/EC Directive,
with particular reference to EN 12445 and EN 12453 standards.
The final connection to the electrical mains, testing and start-up of the automation must be performed by skilled and
qualified personnel (professional gate installers), who is responsible for carrying out the risks analysis and verifying the
compliance of the system with the current safety standards.
This product is exclusively designed and manufactured for the intended use specified in this manual. Any other use than
stated could compromise the integrity and the safety of the product and therefore is strictly prohibited. The automation
is designed to move driveway gates and not intended to be used for any other purpose.
Do not let children play with the radio transmitters and any other device which could accidentally start the gate
automation.
Use exclusively original parts by manufactured by Proteco for maintenance.
Do not carry out any alteration on the components of the automatic gate.
The manufacturer declines all liability in case components or additional devices not produced by MYGATE.
CE COMPLIANCE DECLARATION
MYGATE is a trademark by PROTECO S.r.l.
Manufacturer:
PROTECO S.r.l.
Address:
Via Neive, 77 – 12050 Castagnito (CN) – ITALIA
declares that
The product type: STRIKE Electromechanical gear motor for sliding gate
Models: STRIKE 4, STRIKE 5, STRIKE 8
Is built to be integrated into a machine or to be assembled with other machinery to crate a machine under provisions of 2006/42/EC Machinery
Directive, with reference in particular to the following requirements: 1.1.2, 1.1.3, 1.1.5, 1.2.1, 1.2.2, 1.2.3, 1.2.4.1, 1.2.6, 1.3.1, 1.3.4, 1.3.7, 1.3.8.2, 1.3.9,
1.4.1, 1.4.2.1, 1.4.2.2, 1.5.1, 1.5.4, 1.6.1, 1.6.2, 1.6.3, 1.6.4, 1.7.1, 1.7.3, 1.7.4, 1.7.4.1, 1.7.4.2, 1.7.4.3.
It complies with the essential requirements of EEC Directives:
2006/95/EC
Low Voltage Directive
2004/108/EC
Electromagnetic Compatibilità Directive
The product also complies, with the constraints of the applicable parts, with the following standards:
EN 12453, EN 12445, EN 12604, EN12605, EN 13241-1
EN 55014-1,EN 55014-2
EN 60335-1, EN 60335-2-103
EN 61000-3-2
EN 61000-3-3
The manufacturer also declares that the start-up of the machinery is not permitted unless the machine, in which the product is incorporated or of
which is becoming a component, has been identified and declared as conformed to 2006/42/EC Machinery Directive.
Castagnito, 11th November 2011
Angela Gallo
Amministratore Delegato
2. PRODUCT DESCRIPTION AND INTENDED USE
STRIKE gear motor is designed to automate residential or commercial sliding gate with rack.
Any other use than above described has to be considered as inappropriate and strictly prohibited.
All models feature an irreversible gearing system that locks the gate when it is in its fully closed position. Therefore
no additional lock is needed. In case of a power failure the motor lock can be released to move the gate manually
(see section 6).
The STRIKE 4 version, 24 Volts, can also be powered by a back-up battery system that allows emergency openings
even in case of a power cut.
ENGLISH
