Mychef Bake Technical & Service Manual Download Page 62 | Manualshive

Page: 62 / 71

background image

mychefcooking.com

TECHNICAL SUPPORT SERVICE MANUAL iCOOK | iBAKE | COOK | BAKE | SNACK | BAKERSHOP - DT.MS.CB.2202.2

62

The heating element can then be pulled out by pulling it from inside the cooking chamber.

Remove the heater and proceed with the replacement. When replacing the heating
element, make sure that the gasket between the heating element and the chamber is
replaced. At the back of the oven, make the wiring connections.

5.13.

Replacement of the suction solenoid

Remove the rear of the oven (see  1.1). Then cut the two solenoid wires, leaving enough
length  to  make  a  new  splice.  Remove  the  two  screws  from  the  solenoid  and  remove  it.
Remove the rubber seal and place it on the new solenoid. Remember to splice the wires.

Disassembly of the solenoid

«
...
60
61
62
63
64
...
»

Summary of Contents for Bake








































































Reviews:

No comments

Related manuals for Bake

Brand: Raco Pages: 3

Brand: Weston Pages: 48

Brand: Presto Pages: 3

Brand: Scarlett Pages: 13

Brand: Randell Pages: 14

Brand: Randell Pages: 2

Brand: Adler Pages: 56

Brand: KitchPRO Pages: 20

Brand: Westinghouse Pages: 24

TURBOWAVEbio TT-FD9

Brand: TurboTronic Pages: 36

Brand: Star Pages: 8

Wine Master 180

Brand: Caso Pages: 134

Brand: Bunn Pages: 27

MASTERCHEF LINE TERMOROBOT WiFi PSC-11

Brand: Sam Cook Pages: 62

Brand: Aroma Professional Pages: 104

Brand: Orbegozo Pages: 22

Brand: UFESA Pages: 56

Brand: Salton Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands